background image

REVERSIBLE DEL 3/8"    CAPEZA DEL ANGULO

TALADRO DE AIRE 

®

Rev. 10/07/05

ADVERTENCIA

Se sabe que el polvo generado por el lijado, la aserradura, el esmerilado, la perforación 

mecánica y por otras actividades de construcción contiene químicos que producen cáncer, 

malformaciones congénitas u otros daños relacionados con la reproducción. Algunos  

ejemplos de estos químicos son:

•   Plomo de pintura a base de plomo,
•   Sílice cristalina de ladrillos y cementos y otros productos de mampostería, y 
•   Arsénico y cromo de maderas tratadas químicamente.

El riesgo ante estas exposiciones varía, dependiendo de cuan frecuente usted haga este 

tipo de trabajo. Para reducir la exposición a estos químicos: trabaje en espacios bien 

ventilados, y trabaje con equipos de seguridad aprobados, tales como las mascarillas 

contra el polvo diseñadas específicamente para detener partículas microscópicas.

LEA SIEMPRE LAS 

INSTRUCCIONES 

ANTES DE USAR  

HERRAMIENTAS 

NEUMÁTICAS.

USE SIEMPRE 

GAFAS DE 

SEGURIDAD.

USE 

PROTECCIÓN 

PARA LOS OÍDOS.

EVITE EXPONERSE 

PROLONGADAMENTE 

A LAS VIBRACIONES

6-787

6-787_Manual_100705.indd   7

10/7/05   8:16:27 AM

Summary of Contents for 6-787













Reviews: