NAPCO iBridge Suite, Quick Start Manual

8 

5.  When the configuration keypad powers up, its display will read "

XX OUT OF SYSTEM RCM MODULE

".  

IMPORTANT: 

After the display reads "

XX OUT OF SYSTEM

" , you MUST stop and wait for the IBR-ZREMOTE 

components to reset and prepare for communication; only after the display changes to "

XX OUT OF SYSTEM 

RCM 

MODULE

"  may you proceed with the next step (the words "

RCM-MODULE

"  must be in the display text). 

6. Press 

1 1 1 2 3 FUNCTION

 (or 

MENU

) to enter Keypad Configuration Mode. 

7. Tap 

FUNCTION

 (or 

MENU

) repeatedly until the configuration keypad displays "

Keypad Address

". 

8.  Enter the correct address and tap 

ON/OFF

 (or 

ENTER

) to save.  (

Note:

  The keypad address will not change until 

you tap 

ON/OFF

 or 

ENTER

). 

9. Tap 

FUNCTION

 (or 

MENU

) repeatedly until the keypad displays "

Keypad TYPE RP1CAE2

". 

10. Tap 

INTERIOR / STAY

 or 

NEXT

 to toggle between the keypad model names.  When selected, tap 

ON/OFF

 (or 

ENTER

) 

to save, then tap 

RESET

 to exit.  

Note:

 If using a Stay/Away keypad you 

MUST 

press and hold

STAY 

to change the 

keypad type.  The keypad will then revert back to "

Keypad Beep ON

"; scroll to Keypad Type to verify it is set to "

K1CA

". 

11.  Return the control panel 

CONFIG 

jumper back to the top two pins ("

NORM

").  "System Ready" should appear on 

the keypad if all zones are closed.  

12.  Disconnect the programming cable from the IBR-ZREMOTE and replace jumper 

J4

 that was removed in step 2. 

USING AN APP TO CONFIGURE THE IBR-ZREMOTE

1.  Install the iBridge APP on your Android, iPad or iPhone Device.  Apps can be obtained from 

Google Play 

or the 

Apple Store

. 

2.  Connect to the ISEE-WAP Wi-Fi access point "

IBRIDGE

" using the WEP key 

1234567890 

or connect your device to 

the customers Wi-Fi Network to access the iBridge (verify that you are connected to the iBridge by launching the 
APP, and your status should display "System Ready" or display the keypad status correctly). 

3.  Put the control panel into Keypad Configuration Mode by moving the configuration jumper to the bottom two pins 

("

CONFIG

" ), located inside the control panel.  

4.  Using the iBridge app, at the Home screen tap "

SECURITY

" then "

OTHER OPTIONS

" and select "

KEYPAD 

MODE

" .  After putting the control panel into Keypad Configuration Mode, it normally takes up to 40 seconds 

for the keypad on the iBridge APP to go "out of system".  The keypad will display "

01 Out of System RCM 

MODULE

".  

IMPORTANT:

  After the display reads "

XX OUT OF SYSTEM

" , you MUST stop and wait for the 

IBR-ZREMOTE components to reset and prepare for communication; only after the display changes to "

XX OUT OF 

SYSTEM 

RCM MODULE

"  may you proceed with the next step (the words "

RCM-MODULE

"  must be in the 

display text). 

5. Press 

1 1 1 2 3 FUNCTION

 (

or MENU

) to enter Keypad Configuration Mode.  

Note:

  Do NOT change the Virtual 

PBX, Account ID or Dealer ID. 

6. Tap 

FUNCTION

 (or 

MENU

) repeatedly until the configuration keypad displays "

Keypad Address

". 

7.  Enter the correct address and tap 

ON/OFF

 (or 

ENTER

) to save.  (

Note:

  Keypad address will not change until you 

tap 

ON/OFF

 or 

ENTER

). 

8. Tap 

FUNCTION

 (or 

MENU

) repeatedly until the keypad displays "

Keypad TYPE RP1CAE2

". 

9. Tap 

INTERIOR / STAY

 or 

NEXT

 to toggle between the keypad model names.  When selected, tap 

ON/OFF

 or 

ENTER

 to save, then tap 

RESET

 to exit. 

10.  Return the control panel 

CONFIG 

jumper back to the top two pins ("

NORM

").  "System Ready" should appear on 

the keypad if all zones are closed. 

If you are using the IBR-ITAB wireless tablet and you are unable to connect with the IBR-ZREMOTE using the APP, then 
the "

USING THE IBR-ITAB TO CONFIGURE THE IBR-ZREMOTE

"  procedure (below) can be used.   

USING THE IBR-ITAB TO CONFIGURE THE IBR-ZREMOTE 

If step 4 was completed properly, the IBR-ZREMOTE and ISEE-WAP should have obtained IP addresses and be ready for 
use.  Power up an IBR-ITAB and it will connect to the ISEE-WAP and IBR-ZREMOTE automatically (this process may take 
several minutes the first time it is performed).  The top status bar will display "

System Ready

" or "

Not Ready to Arm

" when 

it is ready for the following steps: 

Set the keypad skin and configure the IBR-ITAB as follows: 
1.  On the IBR-ITAB: 

a. 

Press and hold 

the 

System Settings 

"gear" icon (located at the lower left corner of the display) for 4 seconds.  

b.  Tap the empty field.  In the keyboard, type the administrator password "

admin

". 

c. Tap 

Done 

and then 

OK

.  

d. Tap 

Yes 

to the "Making System Changes…" popup to proceed. 

2.  Once in the Dealer Settings menu, tap 

Security

.