6.
Insert Antenna
and tight-
en
by hand
until snug.
7.
Repower the radio
by re-
connecting the positive
+VDC
+PWR
wire to termi-
nal
TB1
. Wait 2 minutes for
all devices to fully power
before proceeding.
ELECTRICAL RATINGS
Primary Operating Supply
3VDC from SLE radio main
PC board. 45mA maximum
current draw.
Tighten with 5/16" wrench
(do not over-tighten).
For radios with a
metal
housing, follow steps
5C
and
5D
.
For radios with a
plastic
housing, follow steps
5A
and
5B
.
5C.
Metal Housings:
Remove
the knockout located at the
top of the metal housing, to
the right of the existing an-
tenna (arrow in Fig. 5C).
5D.
Metal Housings:
The other end of the
Antenna Wire
Plug
is an "
Antenna Socket
" (see Fig. 5D).
As shown in Fig. 5D, place
washer "
A
" followed by a
washer "
B
" on this
Antenna
Socket
, then insert the
An-
tenna Socket
into the
knockout hole from inside the
enclosure.
With the threads of the
Anten-
na Socket
extending
through the top of the metal
housing, place another wash-
er "
B
" followed by the metal
washer "
C
" on the
Antenna
Socket
. Secure with the nut
"
D
" and tighten with a 5/16"
wrench (do not over-tighten).
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from
manufacturing defects in materials and workmanship for
thirty-six months
following
the date of manufacture. NAPCO will, within said period, at its option, repair or replace
any product failing to operate correctly without charge to the original purchaser or
user.
This warranty shall not apply to any equipment, or any part thereof, which has been
repaired by others, improperly installed, improperly used, abused, altered, damaged,
subjected to acts of God, or on which any serial numbers have been altered, defaced
or removed. Seller will not be responsible for any dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. THERE IS NO EXPRESS
OR IMPLIED WARRANTY OF MERCHANTABILITY OR A WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS
IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF
NAPCO.
Any action for breach of warranty, including but not limited to any implied warranty of
merchantability, must be brought within the six months following the end of the
warranty period. IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE
IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional who installed and maintains your
security system. In order to exercise the warranty, the product must be returned by
the security professional, shipping costs prepaid and insured to NAPCO. After repair
or replacement, NAPCO assumes the cost of returning products under warranty.
NAPCO shall have no obligation under this warranty, or otherwise, if the product has
been repaired by others, improperly installed, improperly used, abused, altered,
damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any
serial numbers have been altered, defaced or removed. NAPCO will not be
responsible for any dismantling, reassembly or reinstallation charges.
This warranty contains the entire warranty. It is the sole warranty and any prior
agreements or representations, whether oral or written, are either merged herein or
are expressly cancelled. NAPCO neither assumes, nor authorizes any other person
purporting to act on its behalf to modify, to change, or to assume for it, any other
warranty or liability concerning its products.
In no event shall NAPCO be liable for an amount in excess of NAPCO's original
selling price of the product, for any loss or damage, whether direct, indirect, incidental,
consequential, or otherwise arising out of any failure of the product. Seller's warranty,
as hereinabove set forth, shall not be enlarged, diminished or affected by and no
obligation or liability shall arise or grow out of Seller's rendering of technical advice or
service in connection with Buyer's order of the goods furnished hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED
WEEKLY.
Warning:
Despite frequent testing, and due to, but not limited to, any or all of the
following; criminal tampering, electrical or communications disruption, it is possible for
the system to fail to perform as expected. NAPCO does not represent that the
product/system may not be compromised or circumvented; or that the product or
system will prevent any personal injury or property loss by burglary, robbery, fire or
otherwise; nor that the product or system will in all cases provide adequate warning or
protection. A properly installed and maintained alarm may only reduce risk of burglary,
robbery, fire or otherwise but it is not insurance or a guarantee that these events will
not occur. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON A
CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should
in turn advise the consumer to take any and all precautions for his or her safety
including, but not limited to, fleeing the premises and calling police or fire department,
in order to mitigate the possibilities of harm and/or damage.
NAPCO is not an insurer of either the property or safety of the user's family or
employees, and limits its liability for any loss or damage including incidental or
consequential damages to NAPCO's original selling price of the product regardless of
the cause of such loss or damage.
Some states do not allow limitations on how long an implied warranty lasts or do not
allow the exclusion or limitation of incidental or consequential damages, or
differentiate in their treatment of limitations of liability for ordinary or gross negligence,
so the above limitations or exclusions may not apply to you. This Warranty gives you
specific legal rights and you may also have other rights which vary from state to state.
NAPCO LIMITED WARRANTY
Fig. 6: Insert and tighten Antenna
Fig. 5B: A washer on both
sides of "Antenna Mounting
Bracket" (arrows)
"Antenna
Socket"
Fig. 5C: Remove Knockout
Fig. 5D: 4 washers and 1 nut
C
D
A
B
