19
EN
www.napoleongrills.com
N415-0522 OCT 05.18
BI ACCESSORY DRAWER INSTRUCTIONS
BI ACCESSORY DOOR INSTRUCTIONS
1. Unpack the drawer frame assembly.
2. Remove the drawers from the enclosure by fully extending them and then lifting up to remove them from the slides.
3. Shim the opening to ensure that the enclosure fits snuggly into the opening. Ensure that the side shims are located
at the same height as the enclosure mounting holes. The bottom of the opening may need to be shimmed as well to
ensure that the front of the enclosure is plumb.
4. Once the enclosure is level and square, fasten into place. (Fasteners not included).
5. Re-install the drawers by tipping the back of the drawer down into the slide. Once the wheels are inserted into the
slide, lower the front of the drawer until it is level, then push in.
Note
: if the enclosure is installed with shims that are
too thick, the wheel will not engage into the slide. The shim thickness will need to be reduced.
6. Remove the protective coating from all remaining surfaces.
1. Unpack the door and frame.
a. For the curved stainless steel doors, remove the door(s) from the frame by lifting the door while holding on to the
pivot rod. This will allow the pivot rod to come out of the hole on the bottom of the frame. Once the pivot is removed
from the bottom hole, the entire door can be dropped and removed from the frame.
b. For the PF style stainless steel door, the door needs to be removed by loosening the center philips screw on the
hinge furthest away from the door. This will allow the hinge to separate.
c. For double door kits N370-0502-1/N370-0503-1, refer to the instuctions included with the door kit.
2. Center the frame in the opening. Mark the location of the pivot holes, top and bottom. Remember on the PT600
double doors, there will be a pivot rod on both ends. The PF style doors do not have pivot rods. Once all pivot holes
are marked, remove the frame and using a 3/8” drill bit, drill out the clearance holes for the pivot rod. These clearance
holes should be at least 1/2” deep. After the holes are complete, you may once again center the frame in the opening.
Starting with the hinged side, shim between the frame and side wall of the opening. Ensure the shims are close to the
hinge on the PF style doors. When the frame side wall is plumb, fasten it to the cabinet with screws (not provided).
Attach the other side of the frame in the same fashion, ensuring the frame is square.
3. Other than on the curved stainless steel double door kit, fasteners are not required on the top and bottom of the
frame. The curved stainless steel double door frame must be fastened in the center both at the top and bottom.
4. Once the frame has been secured and checked for squareness, the door can be re-installed.
5. Remove the protective coating from all remaining surfaces.
Summary of Contents for BIP500RBNSS3
