background image

EN

W415-1789 / C / 01.29.19

17

  

 

6.0  mounting options

FOR EXTERIOR AND REMOTE EXTERIOR INSTALLATIONS ONLY

note:

Consider blower location carefully as the air flow sound from the blower is more apparent the closer it is to the 
appliance. See “sound considerations” section for details.

!

WARNING

6.1 flush

•  Minimum clearance to combustibles must be maintained or a serious fire hazard could result.
•  DO NOT cover or place any items in the 

Dynamic Heat Control™

 air outlet opening. Failure to comply with 

these instructions will create a fire hazard.

• 

DHC™ Plus CANNOT be mounted directly above or below the appliance vent terminal as this will 

cause the system to fail. It MUST be mounted to the left or right of the appliance vent terminal.

•  For optimal performance, we recommend installing

 DHC™ Plus 

within the top 12” (30.5cm) of the enclosure. 

However, it MUST be installed above the appliance.

•  The minimum height requirement above the appliance will vary depending on the appliance size. See “minimum 

venting requirements” section of your appliance manual for details.

In this mounting option, the wall flashing and exterior housing assembly are flush with the finished exterior wall. 

14 1/2” (36.8cm) by 17 1/4” (44cm) rectangular opening must be framed into the exterior wall

 (see “minimum 

framing requirements” section for details)

.

Top of 

Enclosure

Air Outlet 

Opening

12” 

(30.5cm)

Ø 6” (152mm)

Hole & Installed Collar 

Plate Assembly 

Wall Flashing

Exterior Housing 

Asssembly

Left Side Profile View 

(Remote Exterior Installation illustrated. Some components may not apply 

to your unique installation.)

Exterior

Interior

No materials of any type permitted in this 

area with the exception of an approved 

appliance vent system or the 

DHC™ Plus

 

system.

Air Damper 

Assembly

6’ Rigid 

Steel Venting

(not supplied)

Appliance

(LVX38 Illustrated)

Installed 6” Collar 

Plate Assembly

Exterior Housing 

Assembly

Interior

Exterior

Recommended 

DHC™ Plus

 collar plate 

assembly installation zone (12” [30.5cm]).

Top Side View 

(Remote Exterior Installation illustrated. Some components may not apply to your unique installation.)

Summary of Contents for DHCP-BK









































































Reviews: