background image

30

W415-0763 / B / 10.28.11

8.7 GASKET 

REPLACEMENT

If the glass is not kept clean permanent discolouration and / or 
blemishes may result. Normally a hot fi re will clean the glass. 
The most common reasons for dirty glass include: not using 
suffi cient fuel to get the appliance thoroughly hot, using green 
or wet wood, closing the draft so far that there is insuffi cient air 
for complete combustion. 
If it is necessary to clean the glass, buff lightly with a clean dry 
cloth and non-abrasive cleaner. 

DO NOT CLEAN GLASS WHEN HOT!  

Clean the glass after the fi rst 10 hours of operation with a 

recommended appliance glass cleaner. Thereafter clean as required.

The glass is very strong but do not let burning fuel rest or fall against it and always close the door gently. 

NEVER FORCE IT SHUT! 

If the glass should ever crack or break while the fi re is burning, do not open the door until the fi re is out and do 
not operate the appliance again until the glass has been replaced, available from your Authorized dealer. 

DO 

NOT SUBSTITUTE MATERIALS.

5.3

HOT GLASS WILL 

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

!

WARNING

6.1

If the appliance is equipped with plated parts, you must clean fi ngerprints or other marks from the plated 
surfaces before operating the appliance for the fi rst time. Use a glass cleaner or vinegar and towel to clean. 
If not cleaned properly before operating for the fi rst time, the marks can cause permanent blemishes on 
the plating. After the plating is cured, the fi ngerprints and oils will not affect the fi nish and little maintenance 
is required, just wipe clean as needed.  Prolonged high temperature burning with the door ajar may cause 
discolouration on plated parts.

NOTE: The protective wrap on plated parts is best removed when the assembly is at room 
temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat 
source.

8.8  CARE OF GLASS

8.9  CARE OF PLATED PARTS

At the end of each burning season inspect the shield 
below the secondary air manifold for warping or 
deterioration. Replace if necessary. Both are held to 
the manifold with machine screws. The shield and the 
1/8” fi bre cloth gasket are available from your Wolf 
Steel Ltd. dealer. At this time also check that the door 
gasket is not worn or loose. Replace with 1/2” high 
density fi breglass rope if necessary.

The airwash gasket and shield located inside the 
appliance above the door should also be inspected 
and replaced if deteriorated. 

NOTE: Do not operate appliance if the manifold 
shield, airwash shield or fi bre baffl e is 
deteriorated or missing.

AIRWASH 
SHIELD AND 
GASKET

Summary of Contents for EPA 1100









































Reviews: