background image

 5

WS-415-63 / 11.24.98

VENTING

LOCA

LOCA

LOCA

LOCA

LOCATION AND CLEARANCES

TION AND CLEARANCES

TION AND CLEARANCES

TION AND CLEARANCES

TION AND CLEARANCES

As long as clearance to combustibles is kept within the required distances, the most desirable and benefical location for
a Napoleon Stove is in the centre of a building, thereby allowing the most efficient use of the heat created. The location
of windows, doors and the traffic flow in the room where the stove is to be located should be considered. If possible, you
should choose a location where the vent will pass through the house without cutting a floor or roof joist.

MAINTAIN THESE MINIMUM CLEARANCES TO COMBUSTIBLES:

A.

2"*

B.

2"

C.

1"

D.

17-1/2"

E.

9"

F.

12-1/2"

G.

5"

* with use of heat shield 

GDS16

 only.

The heat shield is required when dimension A is less than 8".

minimum 18" from stove top to ceiling
The stove may be installed into an alcove using 2 heat shields.
NO ADDITIONAL FLOOR PROTECTION IS REQUIRED.

W

W

W

W

WARNING

ARNING

ARNING

ARNING

ARNING

The stove is a direct vented gas-fired room heater. Do not burn wood or other materials in this stove.

Adults and especially children should be alerted to the hazards of high surface temperatures and should

stay away to avoid burns or clothing ignition. Supervise young children when they are in the same room as
the stove.

Due to high temperatures, the stove should be located out of traffic and away from furniture and draperies.

Clothing or other flammable material should not be placed on or near the stove.

Any safety screen or guard removed for servicing must be replaced prior to operating the stove.

It is imperative that the control compartments, burners and circulating blower and its passageway in the

stove and venting system are kept clean. The stove and its venting system should be inspected before use
and at least annually by a qualified service person. More frequent cleaning may be required due to exces-
sive lint from carpeting, bedding material, etc. The stove area must be kept clear and free from combustible
materials, gasoline and other flammable vapours and liquids.

Under no circumstances should this stove be modified.

This stove must not be connected to a chimney flue pipe serving a separate solid fuel burning appliance.

Do not use this stove if any part has been under water. Immediately call a qualified service technician to

inspect the stove and to replace any part of the control system and any gas control which has been under
water.

Do not operate the stove with the glass door removed, cracked or broken. Replacement of the glass should

be done by a licensed or qualified service person.

Do not strike or slam shut the stove glass door.

CARE OF GLASS, PLA

CARE OF GLASS, PLA

CARE OF GLASS, PLA

CARE OF GLASS, PLA

CARE OF GLASS, PLATED AND ENAMELLED P

TED AND ENAMELLED P

TED AND ENAMELLED P

TED AND ENAMELLED P

TED AND ENAMELLED PAR

AR

AR

AR

ARTS

TS

TS

TS

TS

Do not use abrasive cleaners to clean these parts. Buff lightly with a clean dry cloth. Porcelain enamelled components
must be handled with care. The baked-on finish is glass-like. If struck, it will chip! Touch-up paint is available through
your Napoleon dealer.
The glass is 3/16" ceramic glass available from your Napoleon / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERI-
ALS. Clean the glass after the first 10 hours of operation with a recommended gas fireplace glass cleaner. Thereafter
clean as required. DO NOT CLEAN GLASS WHEN HOT! If the glass is not kept clean permanent discolouration and / or
blemishes may result.

Summary of Contents for GDS3700-N



















Reviews: