background image

15

W415-1034 /  09.01.11

6.0 OPERATION

When lit for the fi rst time, the appliance will emit a slight odour for a few hours. This is a normal temporary 
condition caused by the "burn-in" of internal paints and lubricants used in the manufacturing process and 
will not occur again. Simply open a window to suffi ciently ventilate the room. After extended periods of non-
operation such as following a vacation or a warm weather season, the appliance may emit a slight odour for 
a few hours. This is caused by dust particles in the heat exchanger burning off. Open a window to suffi ciently 
ventilate the room.

IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT 

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. 

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH 

THE GLASS DOOR OPENED OR REMOVED.

!

WARNING

6.1  OPERATING AND LIGHTING INSTRUCTIONS

OPERATING INSTRUCTIONS / INSTRUCTIONS D’OPERATION

FOR YOUR SAFETY READ BEFORE OPERATING / POUR VOTRE SÉCURITÉ LIRE AVANT DE FAIRE FONCTIONNER

 

 

 

 
 

 

 

 

 

 

 

 

 

 

 

WARNING:

 IF YOU DO NOT FOLLOW THESE INSTRUC-

TIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT 
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR 
LOSS OF LIFE.
INITIAL LIGHTING OF THE PILOT AND MAIN BURNERS 
MUST BE DONE WITH THE GLASS DOOR OFF.
DO NOT CONNECT VALVE OR WALL SWITCH TO ELEC-
TRICITY. SEE INSTALLATION INSTRUCTIONS.

A. THIS FIREPLACE IS EQUIPPED WITH AN IGNITION DEVICE WHICH AUTOMATI-
CALLY LIGHTS THE PILOT. DO NOT TRY TO LIGHT BY HAND.
B. BEFORE OPERATING SMELL ALL AROUND THE FIREPLACE AREA FOR GAS 
AND NEXT TO THE FLOOR BECAUSE SOME GAS IS HEAVIER THAN AIR AND WILL 
SETTLE ON THE FLOOR.

WHAT TO DO IF YOU SMELL GAS:

‡

 TURN OFF ALL GAS TO THE FIREPLACE.

‡

 OPEN WINDOWS.

‡

 DO NOT TRY TO LIGHT ANY APPLIANCE.

‡

 DO NOT TOUCH ANY ELECTRIC SWITCH

 DO NOT USE ANY PHONE IN YOUR 

BUILDING.

‡

 IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOUR

S PHONE. 

FOLLOW THE GAS SUPPLIER

S INSTRUCTIONS.

‡

 IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE FIRE DEPARTMENT.

C. DO NOT TRY TO REPAIR ANY PART OF THIS ASSEMBLY. CALL A QUALIFIED 
SERVICE TECHNICIAN. FORCE OR ATTEMPTED REPAIR MAY RESULT IN A FIRE 
OR EXPLOSION.
D. DO NOT USE THIS FIREPLACE IF ANY PART HAS BEEN UNDER WATER. 
IMMEDIATELY CALL A QUALIFIED SERVICE TECHNICIAN TO INSPECT THE 
FIREPLACE AND REPLACE ANY PART OF THE CONTROL SYSTEM AND ANY GAS 
CONTROL WHICH HAS BEEN UNDER WATER.

ATTENTION: 

SI CES INSTRUCTIONS NE SONT PAS OBSERVÉES A LA 

LETTRE, UN FEU OU UNE EXPLOSION POURRAIT S

ENSUIVRE 

CAUSANT DES DOMMAGES A LA PROPRIETE, DES BLESSURES 
CORPORELLES OU PERTE DE VIE.
L

 ALLUMAGE INITIAL DE LA VEITLLEUSE ET DU BRULEUR PRINCIPAL 

DOIT SE FAIRE AVEC LA PORTE VITREE ENLEVEE.
NE RACCORDE

=

 PAS LA SOUPAPE OU L

INTERRUPTEUR MURALA 

L

ELECTRICITE.

CONSULTE

=

 LES INSTRUCTIONS D

INSTALLATION.

A. CET APPAREIL EST MUNI D

UN DISPOSITIF D

ALLUMAGE QUI ALLUME LA VEILLEUSE 

AUTOMATIQUEMENT.
N

ESSAYE

=

 PAS D

ALLUMER LA VEILLEUSE MANUELLEMENT.

B. AVANT D

ALLUMER SENTE

=

 L

AIR AUTOUR DE L

APPAREIL ET PR

Ê

S DU PLANCHER (CERTAINS 

GA

=

 SONT PLUS LOURDS QUE L

AIR ET SE DÉPOSERONT AU NIVEAU DU PLANCHER) POUR 

DÉTECTER UNE FUITE POSSIBLE.
QUE FAIRE SI VOUS DÉTECTEZ UNE ODEUR DE GAZ:

‡

 COUPEZ L

ALIMENTATION DE GAZ PRINCIPALE.

‡

 OUVREZ LES FENETRES.

‡

 N

ALLUMEZ AUCUN APPAREIL.

‡

 NE TOUCHEZ PAS 

¬

 AUCUN INTERRUPTEUR ÉLECTRIQUE

 N

UTILISEZ AUCUN TÉLÉPHONE 

DANS VOTRE IMMEUBLE.

‡

 APPELEZ IMMÉDIATEMENT VOTRE FOURNISSEUR DE GAZ D

UN TÉLÉPHONE VOISIN ET SUIVEZ 

SES INSTRUCTIONS.

‡

 SI VOUS NE POUVEZ PAS REJOINDRE VOTRE FOURNISSEUR DE GAZ, APPELEZ LE SERVICE 

DES
INCENDIES.
C. N

ESSAYEZ PAS DE RÉPARER AUCUNE PI

Ê

CE DE CET ASSEMBLAGE. APPELEZ UN 

TECHNICIEN QUALIFIÉ. FORCER OU TENTER DE RÉPARER L

ASSEMBLAGE POURRAIT CAUSER 

UN FEU OU UNE EXPLOSION.
D. N

UTILISEZ PAS CET APPAREIL SI UN DE SES COMPOSANTS 

¬

 ÉTÉ SUBMERGÉ. CONTACTEZ 

IMMÉDIATEMENT UN TECHNICIEN DE SERVICE QUALIFIÉ POUR INSPECTER L

APPAREIL ET 

REMPLACER TOUT SYST

Ê

ME DE CONTR

Ð

LE DE GAZ TOUCHÉ PAR L

EAU.

W385-0460

LIGHTING INSTRUCTIONS / INSTRUCTIONS D’ALLUMAGE

1. 

  

STOP! 

READ ALL INFORMATION OF OPERATING AND LIGHTING 

      INSTRUCTIONS BEFORE PROCEEDING.

2.

   TURN OFF ELECTRIC POWER TO THE FIREPLACE.

3.

   THIS FIREPLACE IS EQUIPPED WITH AN IGNITION DEVICE WHICH 

      AUTOMATICALLY LIGHTS THE PILOT. DO NOT TRY TO LIGHT THE PILOT 
      BY HAND.

4. 

  OPEN THE GLASS DOOR.

5. 

  TURN MANUAL SHUTOFF VALVE CLOCKWISE             TO OFF.

6. 

  WAIT FIVE (5) MINUTES TO CLEAR OUT ANY GAS. IF YOU SMELL GAS 

      INCLUDING NEAR THE FLOOR, 

STOP!

 FOLLOW “B” OF THE OPERATING 

      INSTRUCTIONS. IF YOU DON’T SMELL GAS GO TO THE NEXT STEP.

7. 

  TURN MANUAL SHUTOFF VALVE COUNTER-CLOCKWISE              TO ON.

8. 

  CLOSE THE GLASS DOOR.

9. 

  TURN ON ALL ELECTRIC POWER TO THE FIREPLACE.

10.

   TURN ON MAIN BURNER.

1. 

  

ARRÊTEZ!

 LISEZ TOUTES LES INSTRUCTIONS DE FONCTIONNEMENT 

      ET D’ALLUMAGE AVANT DE CONTINUER.  

2.

   COUPEZ L’ALIMENTATION ÉLECTRIQUE À L’APPAREIL.

3.

   CET APPAREIL EST MUNI D’UN DISPOSITIF D’ALLUMAGE QUI ALLUME 

      LA VEILLEUSE AUTOMATIQUEMENT, N’ESSAYEZ PAS D’ALLUMER LA 
      VEILLEUSE MANUELLEMENT.

4. 

  OUVREZ LA PORTE VITRÉE.

5. 

  TOURNEZ LA SOUPAPE DE SECTIONNEMENT MANUELLE VERS LA 

      DROITE             A “OFF”.

6. 

  ATTENDEZ CINQ (5) MINUTES POUR QUE LE GAZ PUISSE  

      S’ÉCHAPPER. SI VOUS DÉTECTEZ UNE ODEUR DE GAZ, 

ARRÊTEZ!

 

      SUIVEZ « B » DANS LES INSTRUCTIONS DE FONCTIONNEMENT.

 

S’IL

      N’Y A PAS D’ODEUR DE GAZ, PASSEZ À L’ÉTAPE SUIVANTE.

7. 

  TOURNEZ LA SOUPAPE DE SECTIONNEMENT MANUELLE VERS LA 

      GAUCHE              A “ON”.

8. 

  FERMEZ LA PORTE VITRÉE.

9. 

  RÉTABLISSEZ L’ALIMENTATION ÉLECTRIQUE AU FOYER.

10. ALLUMEZ LE BRÛLEUR PRINCIPAL.

1. 

  TURN OFF ALL ELECTRICAL POWER TO THE FIREPLACE IF SERVICE IS 

      TO BE PERFORMED.

2.

   TURN MANUAL SHUTOFF VALVE CLOCKWISE              TO OFF. DO NOT 

      FORCE.

1. 

  COUPEZ L’ALIMENTATION ÉLECTRIQUE AU FOYER SI UN TRAVAIL 

      D’ENTRETIEN DOIT SE FAIRE. 

2.

   TOURNEZ LA SOUPAPE D’ARRÉT MANUELLE VERS LA DROITE 

      À “OFF” NE FORCEZ PAS.

TO TURN OFF GAS / INSTRUCTIONS POUR COUPER LE GAZ

Summary of Contents for IR3GN





































Reviews: