Narex ASV 200-2 BASIC, Operating Manual

English

22

Work mode selection (ASV 200-2 only)

Setting up torque

Turning the mode switch (6a) to the relevant symbol will set the 

required torque�

Tightening

Symbol 

1

= lowest tightening torque

Symbol 

18

  = highest tightening torque

Drilling

Symbol 

  = maximum torque

Work mode selection (ASP 200-2 only)

You can set up tightening, impact free drilling or impact drilling by 

turning the mode switch (6b) to the relevant symbol� You may also 

use the torque set function for batch or gentle tightening when 

setting up the drive mode� The machine has a maximum torque 

available when setting the impact free drilling mode� Impact drill-

ing makes drilling more efficient, e�g� when drilling into brick or 

other such hard construction materials�

Attention!

 Only change the tightening/drilling/impact drilling 

modes while the machine is idle!
Always use only drill bits designed for impact drilling when drilling 

in this manner�

Tightening

Symbol 

  = suitable for tightening�

Impact free drilling

Symbol 

  = suitable for driving, drilling into metal, wood 

etc�

Impact Drilling

Symbol 

  = suitable for impact drilling into brick�

Setting up torque 

The function for setting up torque can be used only if the machine 

or set collar (6b) is set to tightening mode� 
Proceed as per the above to set up torque�

Mounting and releasing tools

Turning the chuck mounting case (8) opens and closes the jaws 

between which you place the working tools (drill bit, bit holder 

etc�)� The machines are automatically equipped with a spindle stop, 

which makes changing the tool using only one hand in the desired 

direction very simple�

Mounting a belt clip

Place the machine onto a horizontal surface (e�g� a work table)� 

Place the belt clip (12) onto the belt clip base (14) so that the 

openings in the belt clip overlap with the threaded openings in the 

machine� Secure the belt clip (12) using fastening screws (13) and 

a corresponding screwdriver� You can mount the belt clip to the 

machine from the right or the left side� Be careful not to mount the 

belt clip the wrong way around� The belt clip position must match 

the illustration�

“TRAFFIC LIGHT” LED indicator (9)

Battery charge status (capacity) indication:

Activates automatically once you press the switch button (3) and 

switches off after approx� 3 seconds� The following LEDs light up 

depending on the state of charge (capacity) of the accumulator:

•  Accumulator is fully charged: all three status LEDs light up – 

green, yellow and red�

•  Accumulator capacity has dropped below ca� 60%: only two 

status LEDs light up – yellow and red�

•  Accumulator capacity has dropped below ca� 30%: only one 

status LED lights up – red�

Indication of Reversible Defects

•  Indication of low accumulator voltage – can occur when the 

accumulator voltage reaches dangerously low levels that 

could prevent repeated, proper and safe recharging� The con-

trol system will automatically disconnect the motor and a red 

status LED will start flashing; release the switch and press it 

again� If the problem persists, take the accumulator out of the 

machine and place it in the charger to recharge it� Insert the 

other (spare) accumulator into the machine and proceed with 

your work� 

•  Overload indication – can occur as a result of excessive cur-

rent consumption, e�g� at an extremely high torque, in case 

of a jammed tool etc� The control system will automatically 

disconnect the motor and all three status LEDs will start flash-

ing – green, yellow and red� To restart the machine, release the 

switch and then press it again�

•  Overheat indicator – can occur in case of a long-term, extreme 

load� The control system will automatically disconnect the mo-

tor and two status LEDs will start flashing – yellow and red� Let 

the machine cool down before using it again� The cool down 

time depends on how overheated the machine is�

Indication of Irreversible Defects

May occur as a result of a combination of factors� e�g� during a short 

circuit, motor failure, accumulator failure etc� All three status LEDs 

will start flashing – green, yellow and red� If the machine cannot be 

restarted as per the above, bring it (along with the accumulator) to 

your nearest authorised service centre�

Table overview of problems and signals:

Problem

Reversible damage

Irreversible 

damage

Voltage too low

Excess load

Overheating

LED indicator

Red flashing

Green, yellow and 

red flashing

Yellow and red 

flashing

Green, 

yellow and red 

flashing

Machine status

Disconnected

Disconnected

Disconnected

Disconnected

Turning the 

machine on 

again

Releasing and pressing the button (3)

Short-term break 

to cool down

Authorised 

service centre

Inserting a 

charged battery

Maintenance and service

Instructions for device cleaning

Start the motor and blow impurities and dust out of the vent holes 

of the device� Use protective goggles for this operation� Clean the 

external plastic parts by a wet rag and mild detergent� Though 

these parts are made of the materials resistant to solvents, 

NEVER 

use any solvent�

Instructions for cleaning the charger

Attention! Risk of electric shock. Prior to start handling 

the charger, disconnect the line plug from the socket!

Impurities and dust can be removed from external charg-

er surfaces by a rag or a non-metal brush� Use neither water nor 

detergents�

 Attention! With respect to protection from el. shock 

and preservation of the class of protection, all mainte-

nance and service operations requesting jig saw case 

removal must be performed by the authorized service 

centre only!

The current list of authorized service centres can be found at our 

website 

www.narex.cz

, section 

“Service centres”

�

Accessories

The accessories recommended for use with this device are availa-

ble commercially in the shops with hand el� tools�

Storage

Packed appliance may be stored in dry, unheated storage place 

with temperature not lower than -5 °C�
Unpacked appliance should be stored only in dry storage place 

with temperature not lower than +5 °C with exclusion of all sudden 

temperature changes�

Environmental protection

Power tools, accessories and packaging should be sorted for envi-

ronmental-friendly recy�

Only for EU countries:

Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri-

cal and electronic equipment and its incorporation into national