English
22
Detachable Handgrip
For safety reasons, always use the device with the detachable
handgrip (8) firmly fastened in the dovetail (9)� Turning the handle
loosens or tightens the dovetail joint�
Mounting a belt clip
Place the machine on a horizontal surface (e�g� a working table)�
Slide the bent end of the belt clip (7a) into the base for the belt
clip (7c)� Secure the belt clip (7a) using a fastening screw (7b) and
a corresponding screwdriver� You can mount the belt clip to the
machine from the right, as well as the left side� Be careful not to
mount the belt clip the wrong way round� The belt clip position
must correspond to the illustration�
Checking Accumulator Status
The machine is fitted with an accumulator status control panel (B3)�
Press the control button (B4) on the accumulator status panel (B3)�
An accumulator status indicator (B5) will light up based on the
state of charge (capacity) of the accumulator�
Overview of accumulator’s state of charge (capacity) indication:
Number of fully lit LEDs
Accumulator's state of charge
3
100 %
2
less than 60 %
1
less than 30 %
Electronic Safeguards
The machine is fitted with circuitry designed to prevent serious
damage to the machine� If the electronics detect any of the faults/
defects below, the machine stops immediately� Remove the fault/
defect by proceeding in accordance with the table�
Overview of safety features and methods for returning the machine to operation:
Type of safety feature
Solution
Low accumulator voltage
(indicated on the accumulator)
Recharge / replace the accu-
mulator
Machine overload (machine
was switched off due to recoil
or excessive load)
Release and then press the
power switch again
Overheating (critical temper-
ature of the motor, the elec-
tronics or the accumulator was
reached)
Let the machine cool off
Maintenance and service
Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes
of the device� Use protective goggles for this operation� Clean the
external plastic parts by a wet rag and mild detergent� Though
these parts are made of the materials resistant to solvents,
NEVER
use any solvent�
Instructions for cleaning the charger
Attention! Risk of electric shock. Prior to start handling
the charger, disconnect the line plug from the socket!
Impurities and dust can be removed from external charg-
er surfaces by a rag or a non-metal brush� Use neither water nor
detergents�
Attention! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service
centre only!
The current list of authorized service centres can be found at our
website
www.narex.cz
, section
“Service centres”
�
Accessories
The accessories recommended for use with this device are availa-
ble commercially in the shops with hand el� tools�
Storage
Packed appliance may be stored in dry, unheated storage place
with temperature not lower than -5 °C�
Unpacked appliance should be stored only in dry storage place
with temperature not lower than +5 °C with exclusion of all sudden
temperature changes�
Environmental protection
Power tools, accessories and packaging should be sorted for envi-
ronmental-friendly recy�
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri-
cal and electronic equipment and its incorporation into national
law, power tools that are no longer suitable for must be separately
collected and sent for recovery in an environmental-friendly man-
ner�
Warranty
Our equipment is under warranty for at least 12 months with re-
gard to material or production faults in accordance with national
legislation� In the EU countries, the warranty period for exclusively
private use is 24 months (an invoice or delivery note is required as
proof of purchase)�
Damage resulting from, in particular, normal wear and tear, over-
loading, improper handling, or caused by the user or other dam-
age caused by not following the operating instructions, or any
fault acknowledged at the time of purchase, is not covered by the
warranty�
Complaints will only be acknowledged if the equipment has not
been dismantled before being sent back to the suppliers or to an
authorised NAREX customer support workshop� Store the operat-
ing instructions, safety notes, spare parts list and proof of purchase
in a safe place� In addition, the manufacturer’s current warranty
conditions apply�
Note
Due to continuous research and development work, we reserve
the right to make changes to the technical content of this docu-
mentation�
