English
16
Angular grinder EBU 115‑9, EBU 115‑11
Original operating manual (EN)
Description of the device
1 ........Switch
2 ........Vent holes
3 ........Lock spindle pin
4 ........Gearbox
5 ........Clamping collet
6 ........Spindle
7a ......Protective guard for grinding
7b .....Protective guard for cutting
*
8 ........Guide lugs
9 ........Clamping bolt
10 ......Bottom flange
11 ......Wheel
*
12 ......Clamping nut
*
13 ......Quick-clamping nut
*
14 ......Clamping nut recess
15 ......Wrench
16 ......Additional handle
17 ......Hexagonal wrench dia. 4 mm
18 ......Lever
*) Depicted or displayed accessories need not necessarily become
the integral part of delivery.
Technical Specification
Model
EBU 115‑9
EBU 115‑11
Voltage (V)
230
230
Mains frequency (Hz)
50–60
50–60
Power input (W)
900
1 100
Idle speed (rpm)
10 000
10 000
Grinding/cutting wheel dia. max. (mm)
115
115
Additional handle SOFTGRIP
Circumferential speed (m/s)
80
80
Work spindle thread
M 14
M 14
Limits to interaction current
Switching off during back thrust
Protection against re-starting
Constant electronics
û
û
Weight without tool (kg)
1.8
1.9
Class of protection
II /
II /
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference!
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a)
Keep work area clean and well lit.
Cluttered or dark areas invite
accidents.
b)
Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust.
Power tools
create sparks which may ignite the dust or fumes.
c)
Keep children and bystanders away while operating a power
tool.
Distractions can cause you to lose control.
2) Electrical safety
a)
Power tool plugs must match the outlet. Never modify the plug
in any way. Do not use any adapter plugs with earthed (ground‑
ed) power tools.
Unmodified plugs and matching outlets will re-
duce risk of electric shock.
b)
Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators.
There is an increased
risk of electric shock if your body is earthed or grounded.
c)
Do not expose power tools to rain or wet conditions.
Water en-
tering a power tool will increase the risk of electric shock.
d)
Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat, oil,
sharp edges or moving parts.
Damaged or entangled cords in-
crease the risk of electric shock.
e)
When operating a power tool outdoors, use an extension cord
suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f)
If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply.
Use of an RCD
reduces the risk of electric shock.
3) Personal safety
a)
Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result
in serious personal injury.
b)
Use personal protective equipment. Always wear eye protec‑
tion.
Protective equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate con-
ditions will reduce personal injuries.
Table of contents
Description of the device ..........................................................................16
Technical Specification ..............................................................................16
General Power Tool Safety Warnings ......................................................16
Special Safety Instructions .......................................................................17
Information about noise level and vibrations .......................................18
Double insulation ......................................................................................18
Use ................................................................................................................18
Protective elements and their assembly ................................................18
Grinding or cutting wheel fixing ..............................................................19
Putting into operation ...............................................................................19
Motor electronics .......................................................................................19
Grinding and cutting discs .......................................................................19
Maintenance and service ..........................................................................19
Storage ........................................................................................................19
Environmental protection ........................................................................19
Warranty .....................................................................................................20
Certificate of Conformity ..........................................................................20
Summary of Contents for EBU 115-9
