Narex EVP 13 G-2H3, Original Operating Manual

English

14

Impact drill EVP 13 G-2H3, EVP 13 G-2A

Original operating manual

Table of contents

1  Safety warnings ................................................................ 14

1.1  General Power Tool Safety Warnings ...................................14
1.2  Special safety instructions for drills ......................................15
1.3  Further safety instructions .....................................................15
1.4  Other risks .................................................................................15

2  Information about noise level and vibrations ................. 15
3  Technical Specification...................................................... 16
4  Machine Description ......................................................... 16
5  Double insulation .............................................................. 16
6 Use ...................................................................................... 16
7 Commissioning .................................................................. 16

7.1  Additional handle ...................................................................17
7.2  Clamping of drill bits ...............................................................17
7.3  Switching on and off ...............................................................17
7.4  Permanent run .........................................................................17
7.5  Speed control ...........................................................................17
7.6  Electronic speed pre-selection ...............................................17
7.7  Gear shifting  ............................................................................17
7.8  Change in rotation  .................................................................17
7.9  Drilling and impact drilling ...................................................17
7.10  Removing the chuck with ring gear (Fig.) ............................17
7.11  Removing the quick-tightening chuck (Fig.) .......................17
7.12  Power Plug ................................................................................17

8  Work instructions .............................................................. 17
9  Maintenance and service .................................................. 18
10 Accessories ......................................................................... 18
11 Storage............................................................................... 18
12  Environmental protection ................................................ 18
13 Warranty ............................................................................ 18
14  Certificate of Conformity .................................................. 18

1  Safety warnings

1.1  General Power Tool Safety Warnings

WARNING!

 Read all safety warnings and all instruc-

tions. 

Failure to follow the warnings and instructions 

may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference!

The term “power tool” in the warnings refers to your mains‑operat‑

ed (corded) power tool or battery‑operated (cordless) power tool.

1)  Work area safety

a) 

Keep work area clean and well lit.

 Cluttered or dark areas 

invite accidents.

b) 

Do  not operate power tools in explosive atmospheres, 

such as in the presence of flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or fumes.

c) 

Keep children and bystanders away while operating a pow-

er tool.

 Distractions can cause you to lose control.

2)  Electrical safety

a) 

Power tool plugs must match the outlet. Never modify the 

plug in any way. Do not use any adapter plugs with earthed 

(grounded) power tools.

 Unmodified plugs and matching 

outlets will reduce risk of electric shock.

b) 

Avoid body contact with earthed or grounded surfaces, 

such as pipes, radiators, ranges and refrigerators.

 There is 

an increased risk of electric shock if your body is earthed or 

grounded.

c) 

Do not expose power tools to rain or wet conditions.

 Water 

entering a power tool will increase the risk of electric shock.

d) 

Do  not abuse the cord. Never use the cord for carrying, 

pulling or unplugging the power tool. Keep cord away 

from heat, oil, sharp edges or moving parts.

 Damaged or 

entangled cords increase the risk of electric shock.

e) 

When operating a power tool outdoors, use an extension 

cord suitable for outdoor use.

 Use of a cord suitable for out-

door use reduces the risk of electric shock.

f) 

If operating a power tool in a damp location is unavoida-

ble, use a residual current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3)  Personal safety

a) 

Stay alert, watch what you are doing and use common 

sense when operating a  power tool. Do  not use a  power 

tool while you are tired or under the influence of drugs, 

alcohol or medication.

 A moment of inattention while oper-

ating power tools may result in serious personal injury.

b) 

Use personal protective equipment. Always wear eye pro-

tection.

 Protective equipment such as dust mask, non-skid 

safety shoes, hard hat, or hearing protection used for appro-

priate conditions will reduce personal injuries.

c) 

Prevent unintentional starting. Ensure the switch is in the 

off-position before connecting to power source and/or bat-

tery pack, picking up or carrying the tool.

 Carrying power 

tools with your finger on the switch or energising power tools 

that have the switch on invites accidents.

d) 

Remove any adjusting key or wrench before turning the 

power tool on.

 A wrench or a key left attached to a rotating 

part of the power tool may result in personal injury.

e) 

Do not overreach. Keep proper footing and balance at all 

times.

 This enables better control of the power tool in unex-

pected situations.

f) 

Dress properly. Do  not wear loose clothing or jewellery. 

Keep your hair, clothing and gloves away from moving 

parts.

 Loose clothes, jewellery or long hair can be caught in 

moving parts.

g) 

If devices are provided for the connection of dust extrac-

tion and collection facilities, ensure these are connected 

and properly used.

 Use of dust collection can reduce dust-re-

lated hazards.

4)  Power tool use and care

a) 

Do not force the power tool. Use the correct power tool for 

your application.

 The correct power tool will do the job better 

and safer at the rate for which it was designed.

b) 

Do not use the power tool if the switch does not turn it on 

and off.

 Any power tool that cannot be controlled with the 

switch is dangerous and must be repaired.

c) 

Disconnect the plug from the power source and/or the 

battery pack from the power tool before making any ad-

justments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting 

the power tool accidentally.

d) 

Store idle power tools out of the reach of children and 

do  not allow persons unfamiliar with the power tool or 

these instructions to operate the power tool.

 Power tools 

are dangerous in the hands of untrained users.

e) M

aintain power tools. Check for misalignment or binding 

of moving parts, breakage of parts and any other condi-

tion that may affect the power tool’s operation. If dam-

aged, have the power tool repaired before use.

 Many acci-

dents are caused by poorly maintained power tools.

f) 

Keep cutting tools sharp and clean.

 Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 

and are easier to control..

g) 

Use the power tool, accessories and tool bits etc. in ac-

cordance with these instructions, taking into account the 

working conditions and the work to be performed.

 Use of 

the power tool for operations different from those intended 

could result in a hazardous situation.