background image

PTA12-000 POTS Telephone Adapter Manual  

SM55 Rev. 4.00 

Front Panel 

Aluminum, with Lexan label and Elastomeric keypad. 
Front panel is not backlit. Silicone rubber, tactile push-
buttons backlit by amber LEDs. 

 

Mounting 

Dzus rail (4 fasteners). 

 

Material/Finish 

Chassis & cover are 5052-H32 brushed aluminum with 
chromate conversion finish 

 

Connectors 

 

One male filtered 25 pin D-min with Positronics V5 
locking tabs 

 

1.4.3 Environmental 

Specifications 

 Operating 

Temperatures 

-20

°

 C to +55

°

 C 

 

 Survival 

Temperatures 

-55

°

 C to +85

°

 C 

 

 Vibration/Shock 

 DO-160D 

Cat. 

[(SBM)(UF)] 

 

 Humidity 

  > 

95% 

 

 Altitude   50,000 

ft. 

 

 Compliance: 

 

DO-160D Env. Cat. A1/D1-BAB[(SBM)(UF)]XXXXXXZBABB[UTX]MXXXX. 

1.5 

Accessories Required But Not Supplied 

Installation kit p/n PTA12-IKC (crimp) or PTA12-IKS (solder) is required to complete the 
installation.  They consist of the following: 

 

PTA12-IKC

 25-pin D-min Female Crimp Kit (NAT Part No. D25SV-IKC) 

 

Quantity 

Description 

NAT Part # 

 

D-min 25 Socket housing 

20-21-025 

25 

MS Crimp Socket 

20-26-901 

25 Pin JVL Hood/Locklever 

20-29-250 

 

PTA12-IKS

 25-pin D-min Female Solder Kit (NAT Part No. D25SV-IKS) 

 

Quantity 

Description 

NAT Part # 

 

D-min 25 Socket Solder Cup 

20-20-025 

25 Pin JVL Hood/Locklever 

20-29-250 

 
 

End of section 1.0

 

Page 1-4 

Nov 12, 2003 

ENG-FORM: 800-0106.DOT 

 

 

CONFIDENTIAL AND PROPRIETARY TO NORTHERN AIRBORNE TECHNOLOGY LTD.

 

Summary of Contents for PTA12-000

























Reviews: