background image

Page 8 

    National Communications

MESSAGE ON HOLD - INSTALLATION

Where an existing RADIO, CD or TAPE player

is being replaced

1.

Disconnect Power to the existing audio device.

2.

Disconnect the Audio Output Cord of the existing Line
Isolation Unit (LIU) from the existing audio device.

Note - An LIU (Line Isolation Unit) is  used to connect Audio
from the AUX or HEADPHONE outlet of the existing device
through to the telephone system.
This is an ACMA safety requirement.

3.

Connect the Audio Output Cord of the existing LIU to the
3.5mm Audio Output connector of your 

DMS

 unit.

Note - If the existing LIU does not use a 3.5mm Audio Plug,
then you will need to replace the existing LIU with a new
LIU which has a 3.5mm Audio Plug. These are available
from National Communications (ph 07 55965128).

4.

Power Connection

A 12VAC/1A power adaptor is supplied with your unit. This
must be connected to an electrical power outlet, which is
switched ON.

5.

Message Volume Adjustment

Place a call to the telephone system, put the call ON HOLD
and adjust the volume to a suitable level using the volume
pot located on  the rear of  

DMS

. Turning the POT clockwise

will increase the volume.

Summary of Contents for DMS

















Reviews: