background image

Natcomm  

Page 11

 

 

FCC (USA) and IC (Canada) COMPLIANCE 

 

This product has been tested by an authorized independent laboratory to comply with 
all Telephone Line and Electromagnetic Compliance requirements for the USA and 
Canada.  

REQUIRED RADIO FREQUENCY STATEMENT 

This equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to Part 15 of the FCC rules.   

It has also been tested and found to comply with the limits for CS-003 of the 
Industry Canada rules.   

These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates and can 
radiate radio frequency energy within FCC and IC limits. If not installed and 
used in accordance with these instructions, it may be possible that it causes 
interference to radio communications. However, there is no guarantee that the 
interference will not occur in a particular installation. 

If this equipment does cause interference to radio or television reception, which 
can be determined by testing with the TLM equipment turned off, the user is 
encouraged to try to correct the interference by one or more of the following 
measures:  

 

Increase the separation between the TLM equipment and the affected 
receiver. 

 

 

Connect the equipment into an outlet on a circuit different from that of 
the receiver. 

 

 

Consult the dealer or an experienced technician for help.

 

 

Call NATCOMM ph 0800 530 8645

 

 

The Power adaptor supplied with the Door Station Controller that powers   this product 
complies with UL (USA) and cUL (Canada) specifications.

  

Summary of Contents for LS1













Reviews: