background image

Assembly Instructions

and Owner’s Manual 

Description:

Quantum® Hardcoated Polycarbonate
UTV Windshield, 

Wash’n’Wipe™

Full Size  

Model: 

Polaris Ranger Full Size, Rd.
Frame Tube, Various Models 

Part Number:

N30208

Installation Time:

60 min.

Thank you for purchasing a National Cycle product. Read these instructions carefully and thoroughly before beginning work.
Dealers, if installing this windshield for a customer, please give them this manual. It contains information needed to properly
maintain and use this product. 

Attention: 

Special notes and cautionary measures which can pre-
vent damage to the accessory or vehicle. 

Note: 

Tips for facilitation of operation, control and adjust-
ment, as well as maintenance work. 

Item

Part No. 

Description 

Qty. 

Notes and Tools 

1

20-290402-000

Windscreen, Upper Section             

1

Grommets Installed

2

20-290433-000

Windscreen, Lower Section

1

Grommets and Velcro Fastener Installed

3

44-447165-000

Grommets for Windshield

Installed on Windscreen

4

77-771152-001

Marine Grade Velcro, Hook

2

Installed on Windscreen

5

77-771153-001

Marine Grade Velcro, Loop   

2

Installed on Windscreen 

6

80-875150-000

Motor Assembly

1

Installed on Windscreen

7

80-875153-000 

Arm, Wiper Assembly, 14” 350mm    

1

Replacement Blade Part No. is N30910

8

80-875155-000 

Blade, Wiper Assembly, 16” (406mm)   

1

Replacement Blade Part No. is N30901

9

44-447002-000 

Foam Tape, 1/8 x 1” W

1

Installed on Windscreen

KIT

10

44-442523-000 

Reservoir & Pump Assembly

1

11

80-830326-000 

Wire Harness and Switch

1

With Grommet and Switch, 

Page 2

Parts Installed on Two-Part Windscreen   

Tools Required 

National Cycle, Inc.

PO Box 158, Maywood, IL 60153-0158

P. 708-343-0400 / F. 708-343-0625 / E. Info@nationalcycle.com   

www.nationalcycle.com

©2015 National Cycle, Inc.

Page 1 of 12

10-118025-000 04/15  

PREPARATION

This Kit has been carefully packed and inspected at the factory. Report any missing part directly to National Cycle, Inc.
along with the Bag No. and Date on outside of Windshield Carton. 

Carefully unpack the windshield, sort the parts, and make sure you have everything required to complete the installation
to the vehicle. 

TOOL LIST

Flat Blade Screwdriver
Marker
X-Acto® Knife, or similar 
Wire Cutters 
Power Drill with 3/4” (19mm)  hole saw, or similar
Small Drill Bit (1/8”) (3mm) for pilot hole
#2 or #3 Phillips Screw Driver or Phillips Bit for Drill 

Parts List Continues on Next Page 

KIT 
RESERVOIR and 
WIRE HARNESS

(Harness, Page 2)

3 x9

1 x1

6 x1

7 x1

8 x1

2 x1

9 x1

4 x2

5 x2

10 x1

Summary of Contents for Quantum Wash'n'Wipe N30208













Reviews: