background image

   National Electronics & Watch Co, Ltd. 

BC10 

 

 

FCC Statement 

 

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions:

 

(1) This device may not cause harmful interference. 
(2) This device must accept any interference received, including interference that 
may cause undesired operation. 

 

2. Changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate the equipment. 

 

NOTE:  

 

This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. 
This equipment generates uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 
Reorient or relocate the receiving antenna. 
Increase the separation between the equipment and receiver. 
Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help. 
 
 

IC STATEMENT 

 

Operation is subject to the following two conditions:  
(1) This device may not cause interference, and  

(2) This device must accept any interference, including interference that may 
cause undesired operation of the device. 

 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux 
appareils radio exempts de licence. L'exploitation est autorisée aux deux 
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) 
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si 
le brouillage est susceptible d'en compromettre le fonctionnement. 

 

Note :
This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme 

NMB-003 du Canada.

Cet appareil numérique de la classe B est conforme à la norme 

Summary of Contents for M11-1908D














Reviews: