Safety
Environment
Avoid use in dangerous environments.
Do not use in rain, damp or wet locations, or in the presence of
H[SORVLYHDWPRVSKHUHVJDVHRXVIXPHVGXVWRUÀDPPDEOHPDWH
-
ULDOV5HPRYHPDWHULDOVRUGHEULVWKDWPD\EHLJQLWHGE\VSDUNV
.HHSZRUNDUHDWLG\DQGZHOOOLWDFOXWWHUHGRUGDUNZRUNDUHDPD\
OHDGWRDFFLGHQWV([WUHPHKHDWRUFROGPD\DIIHFWSHUIRUPDQFH
Protect others in the work area and be aware of surroundings.
3URYLGHEDUULHUVRUVKLHOGVDVQHHGHGWRSURWHFWRWKHUVIURPGHEULV
DQGPDFKLQHRSHUDWLRQ&KLOGUHQDQGRWKHUE\VWDQGHUVVKRXOGEH
NHSWDWDVDIHGLVWDQFHIURPWKHZRUNDUHDWRDYRLGGLVWUDFWLQJWKH
operator and/or coming into contact with the machine. Operator
VKRXOGEHDZDUHRIZKRLVDURXQGWKHPDQGWKHLUSUR[LPLW\6XS
-
SRUWSHUVRQQHOVKRXOGQHYHUVWDQGQH[WWRLQIURQWRIRUEHKLQG
WKHPDFKLQHZKLOHWKHPDFKLQHLVUXQQLQJ2SHUDWRUVKRXOGORRN
EHKLQGWKHPEHIRUHEDFNLQJXS
Do not come within 3 ft. of the machine’s perimeter during
operation.
Guard against electric shock.
(QVXUHWKDWPDFKLQHLVFRQQHFWHGWRDSURSHUO\JURXQGHGRXWOHW
3UHYHQWERGLO\FRQWDFWZLWKJURXQGHGVXUIDFHVHJSLSHVUDGLD
-
WRUVUDQJHVDQGUHIULJHUDWRUV:KHQVFRULQJRUPDNLQJFXWV
DOZD\VFKHFNWKHZRUNDUHDIRUKLGGHQZLUHVRUSLSHV
5
GENERAL RULES FOR SAFE OPERATION
Before use, anyone operating or performing maintenance on this equipment must read and understand this manual, as well as any labels pack-
aged with or attached to the machine and its components. Read the manual carefully to learn equipment applications and limitations, as well
as potential hazards associated with this type of equipment. Keep manual near machine at all times. If your manual is lost or damaged, contact
National Flooring Equipment (NFE) for a replacement.
Personal
Dress properly and use safety gear.
Do not wear loose clothing; it may be caught in moving parts.
Anyone in the work area must wear safety goggles or glasses,
hearing protection during extended use, and a dust mask for dusty
operations. Hard hats, face shields, safety shoes, etc. should be
ZRUQZKHQVSHFL¿HGRUQHFHVVDU\
Maintain control; stay alert.
.HHSSURSHUIRRWLQJDQGEDODQFHDQGPDLQWDLQD¿UPJULS
Observe surroundings at all times and use common sense. Do not
XVHZKHQWLUHGGLVWUDFWHGRUXQGHUWKHLQÀXHQFHRIGUXJVDOFRKRO
or any medication that may cause decreased control.
Keep hands away from all moving parts and tooling.
Wear gloves when changing tooling. Remove tooling when ma-
FKLQHLVQRWLQXVHDQGRUORZHUFXWWLQJKHDGWRWKHÀRRU
Do not force equipment.
Equipment will perform best at the rate for which it was designed.
Excessive force only causes operator fatigue, increased wear, and
reduced control.
Equipment
Use proper parts and accessories.
Only use NFE-approved or recommended parts and accessories.
Using any that are not recommended may be hazardous.
Ensure accessories are properly installed and maintained.
Do not permanently remove a guard or other safety device when
installing an accessory or attachment.
Inspect for damaged parts.
Check for misalignment, binding of moving parts, loose fasteners,
improper mounting, broken parts, and any other conditions that
may affect operation. If abnormal noise or vibration occurs, turn
the machine off immediately. Do not use damaged equipment until
repaired. Do not use if power switch does not turn machine on and
off. For all repairs, insist on only identical NFE replacement parts.
Maintain equipment and labels.
Keep handles dry, clean, and free from oil and grease. Keep cut-
ting edges sharp and clean. Follow instructions for lubricating and
changing accessories. Motor and switches should be completely
enclosed at all times with no exposed wiring. Inspect cord regu-
larly. Labels carry important information; if unreadable or missing,
contact NFE for a free replacement.
Avoid accidental starting; store idle equipment.
When not in use, ensure that the machine is unplugged; do not
turn on before plugging in. Store in a dry, secured place. Remove
tooling when storing, and keep away from children.
Maintenance & Repairs
Begin maintenance work only when the machine is shut
down, unplugged, and cooled down.
Use proper cleaning agents.
(QVXUHWKDWDOOFOHDQLQJUDJVDUH¿EHUIUHHGRQRWXVHDQ\DJJUHV
-
sive cleaning products.
Schedule regular maintenance check-ups.
Ensure machine is properly cleaned and serviced. Remove all
WUDFHVRIRLOFRPEXVWLEOHIXHORUFOHDQLQJÀXLGVIURPWKHPDFKLQH
DQGLWVFRQQHFWLRQVDQG¿WWLQJV5HWLJKWHQDOOORRVH¿WWLQJVIRXQG
during maintenance and repair work. Loose or damaged parts
should be replaced immediately; use only NFE parts.
'RQRWZHOGRUÁDPHFXWRQWKHPDFKLQHGXULQJUHSDLUVRU
make changes to machine without authorization from NFE.
CAUTION! ENSURE PROPER USE OF EXTENSION CORDS. IF AMP DRAW IS HIGHER THAN SHOWN
ON TABLE OR CORD IS LONGER THAN 50 FT, SEE AN ELECTRICIAN.
ASSUMPTIONS: 3% ALLOWABLE VOLTAGE DROP, COPPER CONDUCTORS RATED FOR 75
O
C, 1.25
SAFETY FACTOR, CORD VOLTAGE RATING OF 600VAC, PROPER CORD TYPES (STO, STOW, SOOW).
Amp Draw
Gauge
0-12
14
13-16
12
14-24
10
25-40
8
5
