background image

©

 National Instruments

13

NI 9146 Operating Instructions and Specifications

Restarting the NI 9146 Using the Reset Button

Pressing the Reset button restarts the NI 9146. The FPGA continues to run 
unless you have selected the 

Autoload VI on device reboot

 chassis reset 

option. Refer to the 

Chassis Startup Options

 section for more information.

To restart the NI 9146 in safe mode, hold the Reset button down for about 
5 s, until the Status LED lights yellow, then release the button. The chassis 
reboots and the Status LED starts blinking three times every few seconds. 
The chassis is now in Safe Mode. Refer to the MAX help for information 
about safe mode.

Chassis Startup Options

Table 1 lists the startup options available for the NI 9146. These options 
determine how the chassis behaves when it starts up in various conditions. 
Use the RIO Device Setup utility to select startup options. Access the 
RIO Device Setup utility by selecting 

Start»All Programs»National 

Instruments»NI-RIO»RIO Device Setup

.

Configuring IP Settings

When you power on the NI 9146 for the first time, it boots into safe mode 
because there is no software installed on it. This section describes how to 
configure the IP settings and install software on the chassis.

Complete the following steps.

1.

Launch MAX on the host computer and expand 

Remote Systems

 in 

the MAX configuration tree. MAX lists the NI 9146 as the model name 
of the chassis followed by the serial number, for example, 

NI9146-XXXXXXXX

.

The chassis automatically attempts to connect to the network using 
DHCP. If DHCP is not available, the chassis connects to the network 
with a link-local IP address with the form 

169.254.x.x

. You must 

connect the chassis directly to the host computer to configure it in this 
state.

Table 1.  

NI 9146 Reset Options

Startup Option

Behavior

Do Not Autoload VI

Does not load the FPGA bit stream from flash memory.

Autoload VI on device powerup

Loads the FPGA bit stream from flash memory to the FPGA 
when the chassis powers on.

Autoload VI on device reboot

Loads the FPGA bit stream from flash to the FPGA when you 
reboot the chassis either with or without cycling power. 

Summary of Contents for 9146























Reviews: