background image

NI 9921/9922 Outdoor IP Enclosure Installation Guide

10

ni.com

Understanding IP Ratings

Proper use and installation of an NI WLS-9000 Series device in an NI 9921/9922 outdoor IP enclosure 
provides a minimum IP rating of IP54 from harsh outdoor and industrial environments. An IP rating of 
IP54 protects against entry by dust particles and splashing water from all directions.

The two-digit ingress protection (IP) rating is defined by the IEC 60529 standard and specifies the 
degree to which the enclosures protect against the intrusion of solid particles (represented by the 
first digit) and water (represented by the second digit). 

Table 2 lists the degree of protection.

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible manner. 
NI recognizes that eliminating certain hazardous substances from our products is beneficial to the 
environment and to NI customers.

For additional environmental information, refer to the 

NI and the Environment

 Web page at 

ni.com/environment

. This page contains the environmental regulations and directives with which 

NI complies, as well as other environmental information not included in this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of the product life cycle, all products 

must

 be sent to a WEEE recycling 

center. For more information about WEEE recycling centers, National Instruments WEEE initiatives, 
and compliance with WEEE Directive 2002/96/EC on Waste and Electronic Equipment, 
visit

ni.com/environment/weee

.

Table 2.  

IP Ratings

First Number 

(Protection Against Solid Objects)

Second Number 

(Protection Against Water)

0

No protection

0

No protection

1

Protects against objects greater than 50 mm

1

Protects against vertically dripping water

2

Protects against objects greater than 12.5 mm

2

Protects against direct sprays up to 15° from vertical

3

Protects against objects greater than 2.5 mm

3

Protects against direct sprays up to 60° from vertical

4

Protects against objects greater than 1 mm

4

Protects against direct sprays from all angles

5

Dust-protected (no harmful deposit)

5

Protects against low pressure water jets

6

Dust-tight

6

Protects against high pressure water jets

7

Immersible in water up to 1 m

8

Immersible in water beyond 1 m

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

˅

Ё೑ᅶ᠋

National Instruments

ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

 (RoHS)

DŽ

݇Ѣ

National Instruments

Ё೑

RoHS

ড়㾘ᗻֵᙃˈ䇋ⱏᔩ

ni.com/environment/rohs_china

DŽ

(For information about China RoHS compliance, go to 

ni.com/environment/rohs_china

.)

Summary of Contents for 9921













Reviews: