background image

Figure 3.

 NI 9148 Front View with Dimensions

87.3 mm

(3.44 in.)

165.1 mm

(6.50 in.)

3.1 mm

(0.12 in.)

51.1 mm

(2.04 in.)

36.4 mm

(1.43 in.)

19 mm

(0.75 in.)

NI 9148

POWER

USER FPGA1

STATUS

SAFE MODE
IP RESET

INPUT

19-30 V

20 W MAX

LINK

10/

100

V
C

NC

C

Figure 4.

 NI 9148 Side View with Dimensions

3

X

 

M

4

X

0.7

25 mm

(0.98 in.)

44 mm

(1.73 in.)

23.7 mm

(0.94 in.)

63.1 mm

(2.48 in.)

44.1 mm

(1.74 in.)

The following sections give instructions for the mounting methods. Before using any of these
mounting methods, record the serial number from the back of the chassis. You will be unable
to read the serial number after you have mounted the chassis.

Caution

 

Make sure that no I/O modules are in the chassis before mounting it.

Mounting the Chassis on a Panel

You can use the NI 9905 panel mount kit to mount the NI 9148 on a flat surface. Complete the
following steps to mount the NI 9148 on a panel.
1.

Fasten the chassis to the panel mount kit using a number 2 Phillips screwdriver and two
M4 × 25 screws. National Instruments provides these screws with the panel mount kit.

NI 9148 User Manual

  | 

© National Instruments

  | 

5

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for cRIO-9148
























Reviews: