National Instruments cRIO-FRC Manual Download | Manualshive

Page: 12 / 14

background image

Installing the Module Connector Gasket

1.

Place the chassis face up on the ESD Pad.

2.

Partially remove the backing from the Module Connector Gasket to reveal the adhesive. Take
care to minimize adhesive contact with foreign objects such as fingers or dust.

3.

Lightly place the Module Connector Gasket in the chassis module cavity adhesive side down, and
gently press the gasket over the first connector.

4.

Working from the first connector, gently peel away enough of the backing to press the gasket
down over each connector, taking care not to stretch the gasket too much.

«
...
10
11
12
13
14
»

Summary of Contents for cRIO-FRC















Reviews:

No comments

Related manuals for cRIO-FRC

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: MADRIX Pages: 36

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Brand: Daikin Pages: 48

Brand: Daikin Pages: 77

Brand: Daikin Pages: 32

Brand: Daikin Pages: 46

Brand: Daikin Pages: 14

Brand: Daikin Pages: 16

Brand: Daikin Pages: 1

Brand: Lawler Pages: 6

Brand: Data Aire Pages: 28

Brand: Eaton Pages: 100

Brand: TagMaster Pages: 28

Brand: Sunnen Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands