background image

4. Connect the bootable USB flash drive or the external USB DVD drive to the USB hub.
5. Connect a monitor to the VGA port on the M12 splitter cable.
6. Power on the ISC-178x.
7. Press the <Esc> key on the keyboard to enter the setup utility.
8. Select 

Boot Manager

 in the setup utility.

9. Select the bootable USB flash drive or the DVD drive.
10. Press any key to boot from the recovery media.
11. Follow the on-screen instructions to format the onboard storage and install the operating

system.

Note

 

After restoring the operating system, reinstall any software and drivers onto

the ISC-178x.

Where to Go Next

The following documents and resources contain information you may find helpful as you use

the ISC-178x in an application. Refer to the National Instruments Product Manuals Library at 

ni.com/manuals

 for the most recent versions of product documentation.

Power and I/O Accessory for ISC-178x Smart Cameras User Manual

—Contains

installation and operation instructions for the Power and I/O Accessory for ISC-178x

Smart Cameras.

ISC-178x Getting Started Guide

—Explains how to install and configure the software

necessary to use the ISC-178x, and how to get started using the hardware.

ISC-1780 Specifications

—Contains detailed specifications for the ISC-1780.

ISC-1781 Specifications

—Contains detailed specifications for the ISC-1781.

ISC-1782 Specifications

—Contains detailed specifications for the ISC-1782.

ISC-1783 Specifications

—Contains detailed specifications for the ISC-1783.

Worldwide Support and Services

The NI website is your complete resource for technical support. At 

ni.com/support

, you have

access to everything from troubleshooting and application development self-help resources to

email and phone assistance from NI Application Engineers.
Visit 

ni.com/services

 for NI Factory Installation Services, repairs, extended warranty, and

other services.
Visit 

ni.com/register

 to register your NI product. Product registration facilitates technical

support and ensures that you receive important information updates from NI.
A Declaration of Conformity (DoC) is our claim of compliance with the Council of the

European Communities using the manufacturer’s declaration of conformity. This system

affords the user protection for electromagnetic compatibility (EMC) and product safety. You

38

  | 

ni.com

  | 

ISC-178x User Manual

Summary of Contents for ISC-1783










































Reviews: