National Instruments M Series User Manual Download

Page: 260 / 299

B-35

M Series User Manual

Input Requirements

Refer to the Figure B-41 for the M Series counter/timer circuitry.

Source Period and Pulse Width

Figure B-46 and Table B-30 show the timing requirements for Counter

Source. The

requirements depend on the synchronization mode.

Figure B-46.

Counter n Source Timing Requirements

Table B-29.

Selected Gate to Count Enable Delays

Time

Synchronization

Mode

Gating

Mode

Min (ns)

Max (ns)

80 MHz Source

Edge

0.5

5.0

Level

-1.0

0.5

Other Internal
Source

Edge

1/2 Source Period -

1 ns

1/2 Source

3 ns

Level

1/2 Source Period -

2.5 ns

1/2 Source Period –

1 ns

External Source

Edge

7.5

22.0

Level

6.0

18.0

Table B-30.

Counter n Source Timing

Time

Description

Synchronization

Mode

Min (ns)

Max (ns)

Counter

Source Period

80 MHz Source

12.5

—

Other Internal
Source

25.0

—

External Source

50.0

—

Counter n Source

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for M Series












































































































































































































































































































Search results

Summary of Contents for M Series

Reviews:

Related manuals for M Series

Brands by name

Popular brands

National Instruments M Series, User Manual

Search results

Summary of Contents for M Series

Reviews:

Related manuals for M Series

Brands by name

Popular brands