background image

©

 National Instruments Corporation

17

NI 9148 Operating Instructions and Specifications

CE Compliance

This product meets the essential requirements of applicable European 
Directives as follows:

2006/95/EC; Low-Voltage Directive (safety)

2004/108/EEC; Electromagnetic Compatibility Directive (EMC)

Online Product Certification

Refer to the Declaration of Conformity (DoC) for this product for 
additional regulatory compliance information. To obtain product 
certifications and the DoC for this product, visit 

ni.com/

certification

, search by model number or product line, and 

click the appropriate link in the Certification column.

Environmental Management

NI is committed to designing and manufacturing products in an 
environmentally responsible manner. NI recognizes that eliminating 
certain hazardous substances from our products is beneficial to the 
environment and to NI customers.

For additional environmental information, refer to the 

NI and the 

Environment

 Web page at 

ni.com/environment

. This page contains the 

environmental regulations and directives with which NI complies, as well 
as other environmental information not included in this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of the product life cycle, all products 

must

 be sent to a WEEE 

recycling center. For more information about WEEE recycling centers, National 
Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on 
Waste and Electronic Equipment, visit 

ni.com/environment/weee

.

Battery Replacement and Disposal

Battery Directive

This device contains a long-life coin cell battery. If you need to replace 

it, use the Return Material Authorization (RMA) process or contact an authorized National 
Instruments service representative. For more information about compliance with the 
EU Battery Directive 2006/66/EC about Batteries and Accumulators and Waste Batteries 
and Accumulators, visit 

ni.com/environment/batterydirective

.

Cd/Hg/Pb

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

˅

Ё೑ᅶ᠋

National Instruments

ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

 (RoHS)

DŽ

݇Ѣ

National Instruments

Ё೑

RoHS

ড়㾘ᗻֵᙃˈ䇋ⱏᔩ

ni.com/environment/rohs_china

DŽ

(For information about China RoHS compliance, go to 

ni.com/environment/rohs_china

.)

Summary of Contents for NI 9148





















Reviews: