background image

NI 9437 Getting Started Guide

|

© National Instruments

|

13

Connection Considerations

Keep in mind the following requirements when connecting to the 

NI 9437.

The supply voltage to V

SUP

 must be within the range of 

24 VDC to 250 VDC.

Output devices that you connect to the NI 9437 must be able to 

source enough current to overcome the NI 9437 input load 

(burden). The NI 9437 burden is dynamic and varies 

depending on the input voltage. Refer to the 

NI 9437 

Datasheet

 on 

ni.com/manual

s

 

for more information about 

dynamic burden current on the NI 9437. 

Output devices that you connect to the NI 9437 do not need to 

sink current. The NI 9437 input load current pulls the input 

voltage to a low value when the output device is open, high 

impedance, or not connected. 

The NI 9437 is immune to capacitively coupled transients 

when using the correct debounce time based on the supply 

voltage and the amount of capacitance in your system. Refer to 

the 

NI 9437 Datasheet

 on 

ni.com/manual

s

 

for more 

information about debounce times. 

Connecting more than one wire to a single terminal on the 

NI 9437 requires 2-wire ferrules to create a secure connection.

Summary of Contents for NI 9437

















Reviews: