background image

Storage humidity (IEC 60068-2-30)

5% RH to 95% RH, noncondensing

Pollution Degree

2

Maximum altitude

2,000 m

Indoor use only.

Environmental Management

NI is committed to designing and manufacturing products in an environmentally

responsible manner. NI recognizes that eliminating certain hazardous substances

from our products is beneficial to the environment and to NI customers.

For additional environmental information, refer to the Engineering a Healthy

Planet web page at 

ni.com/environment

. This page contains the environmental

regulations and directives with which NI complies, as well as other environmental

information not included in this document.

EU and UK Customers

 Waste Electrical and Electronic Equipment (WEEE)

—At the end of the

product life cycle, all NI products must be disposed of according to local laws and

regulations. For more information about how to recycle NI products in your region,

visit 

ni.com/environment/weee

.

电子信息产品污染控制管理办法(中国

RoHS

5

40

e

 中国 RoHS

— NI

符合中国电子信息产品中限制使用某些有害物质指令

(RoHS)

。关于

NI

中国

RoHS

合规性信息,请登录

 ni.com/environment/

rohs_china

(For information about China RoHS compliance, go to ni.com/

environment/rohs_china.)

ni.com

12

NI-9852 Getting Started

Summary of Contents for NI 9852














Reviews: