background image

NI 9925 Installation Guide

8

ni.com

Ordering NI IP Rated Cables

Table 1 lists the optional cable accessories for use with the NI 9925. Go to 

ni.com

 for more 

information about these accessories.

Understanding IP Ratings

Proper use and installation of an NI cDAQ-9181/9191 chassis in an NI 9925 outdoor IP54 
enclosure provides a minimum IP rating of IP54 from outdoor and industrial environments. An 
IP rating of IP54 protects against entry by dust particles and splashing water from all directions.

The two-digit ingress protection (IP) rating is defined by the IEC 60529 standard and specifies 
the degree to which the enclosures protects against entry of dust (represented by the first digit) 
and splashing water (represented by the second digit), as shown in Table 2.

Table 1.  

Optional Cable Accessories

NI Part Number

Description

196648-05

IP rated, 5 meter M12 power cable, pigtail

196650-05

IP rated, 5 meter Ethernet cable

196647-01

Cable clamp replacements: two solid grommets and four assorted two-hole split 
grommets

Table 2.  

IP Ratings

1st 

No.

Protection Against Solid Objects

2nd 

No.

Protection Against Water

0

No protection

0

No protection

1

Protects against objects greater than 
50 mm

1

Protects against vertically dripping water

2

Protects against objects greater than 
12.5 mm

2

Protects against direct sprays up to 
15° from vertical

3

Protects against objects greater than 
2.5 mm

3

Protects against direct sprays up to 
60° from vertical

4

Protects against objects greater than 
1 mm

4

Protects against direct sprays from all 
angles

5

Dust-protected (no harmful deposit)

5

Protects against low pressure water jets

6

Dust-tight

6

Protects against high pressure water jets

7

Immersible in water up to 1 m

8

Immersible in water beyond 1 m

Summary of Contents for NI 9925











Reviews: