background image

Using the RESET Button

Pressing the RESET button resets the processor in the same manner as cycling power.

Note

 

The FPGA continues to run unless you select the 

Autoload on Any Device

Reset

 boot option. Refer to the 

Chassis Reset Options

 section for more information.

Understanding LED Indications

Figure 14.

  cRIO-9074XT LEDs

POWER
FPGA
STATUS
USER1

POWER LED

The POWER LED is lit while the cRIO-9074XT is powered on. This LED indicates that the

power supply connected to the chassis is adequate.

FPGA LED

You can use the FPGA LED to help debug your application or easily retrieve application

status. Use the LabVIEW FPGA Module and NI-RIO software to define the FPGA LED to

meet the needs of your application. Refer to 

LabVIEW Help

 for information about

programming this LED.

STATUS LED

The STATUS LED is off during normal operation. The cRIO-9074XT indicates specific error

conditions by flashing the STATUS LED a certain number of times every few seconds, as

shown in the following table

Number of

Flashes Every

Few Seconds

Indication

 

 

1

The chassis is unconfigured. Use MAX to configure the chassis. Refer

to the 

Measurement & Automation Explorer Help

 for information about

configuring the chassis.

2

The chassis has detected an error in its software. This usually occurs

when an attempt to upgrade the software is interrupted. Reinstall

software on the chassis. Refer to the 

Measurement & Automation

Explorer Help

 for information about installing software on the chassis.

NI cRIO-9074XT User Manual and Specifications

  | 

© National Instruments

  | 

15

Summary of Contents for NI cRIO-9074XT


























Reviews: