background image

settings for different chassis revisions. Complete the following steps to restore the BIOS
network settings of the chassis.
1. Move the IP RESET and SAFE MODE switches to the ON position.
2. Push the RESET button to cycle power to the chassis.
3. Configure the IP and other network settings in MAX.
4. Move the IP RESET and SAFE MODE switches to the OFF position.

Note

 

If the chassis is restored to the BIOS network settings, the LabVIEW

run-time engine does not load. You must reconfigure the network settings and

restart the chassis for the LabVIEW run-time engine to load.

cRIO-9074XT Specifications

The following specifications are typical for the range -40 °C to 70 °C unless otherwise noted.

Caution

 

Do not operate the cRIO-9074XT in a manner not specified in this

document. Product misuse can result in a hazard. You can compromise the safety
protection built into the product if the product is damaged in any way. If the product
is damaged, return it to NI for repair.

Network

Network interface

10Base-T and 100Base-TX Ethernet

Compatibility

IEEE 802.3

Communication rates

10 Mbps, 100 Mbps, auto-negotiated

Maximum cabling distance

100 m/segment

RS-232 Serial Port

Maximum baud rate

115,200 bps

Data bits

5, 6, 7, 8

Stop bits

1, 2

Parity

Odd, Even, Mark, Space

Flow control

RTS/CTS, XON/XOFF, DTR/DSR

SMB Connector

Output Characteristics

Minimum high-level output voltage

With -100 µA output current

2.9 V

With -16 mA output current

2.4 V

With -24 mA output current

2.3 V

NI cRIO-9074XT User Manual and Specifications

  | 

© National Instruments

  | 

17

Summary of Contents for NI cRIO-9074XT


























Reviews: