background image

Note

 

For EMC compliance, operate this product according to the documentation.

CE Compliance 

This product meets the essential requirements of applicable European Directives, as follows:

2014/35/EU; Low-Voltage Directive (safety)

2014/30/EU; Electromagnetic Compatibility Directive (EMC)

94/9/EC; Potentially Explosive Atmospheres (ATEX)

Online Product Certification

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance
information. To obtain product certifications and the DoC for this product, visit 

ni.com/

certification

, search by model number or product line, and click the appropriate link in the

Certification column.

Shock and Vibration

To meet these specifications, you must panel mount the system.

Operating vibration

Random (IEC 60068-2-64)

5 g

rms

, 10 Hz to 500 Hz

Sinusoidal (IEC 60068-2-6)

5 g, 10 Hz to 500 Hz

Operating shock (IEC 60068-2-27)

30 g, 11 ms half sine; 50 g, 3 ms half sine;
18 shocks at 6 orientations

Environmental

Refer to the manual for the chassis you are using for more information about meeting these
specifications.

Operating temperature
(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 70 °C

Storage temperature
(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 85 °C

Ingress protection

IP40

Operating humidity (IEC 60068-2-78)

10% RH to 90% RH, noncondensing

Storage humidity (IEC 60068-2-78)

5% RH to 95% RH, noncondensing

Pollution Degree

2

Maximum altitude

2,000 m

Indoor use only.

NI cRIO-9074XT User Manual and Specifications

  | 

© National Instruments

  | 

21

Summary of Contents for NI cRIO-9074XT


























Reviews: