National Instruments NI REM-11115 Getting Started Manual Download

Page: 8 / 14

Figure 3. REM-11115 LEDs

D
UA
E1
E2

Table 3. LED Indicators

LED

LED Color

LED Pattern

Indication

Green

Solid

The REM-11115 is ready for operation.

Flashing

Data is invalid or unavailable.

Green/Yellow Flashing

The REM-11115 cannot communicate with the
connected devices.

Yellow

Solid

The REM-11115 did not detect a valid cycle after power-
on.

Flashing

The REM-11115 is not part of the configuration.

Red

Solid

The REM-11115 has lost connection to the Bus Coupler.

Flashing

The REM-11115 has lost connection to the preceding
adjacent module.

—

Off

The REM-11115 is in reset mode.

Green

Solid

Supply to analog output module present.

—

Off

No supply to analog output modules.

Red

Solid

Supply to analog output module is faulty.

—

Off

Supply to analog output module is OK.

Red

Solid

I/O or channel error has occurred.

—

Off

No error

ni.com

REM-11115 Getting Started Guide

Summary of Contents for NI REM-11115















Search results

Summary of Contents for NI REM-11115

Reviews:

Related manuals for NI REM-11115

Brands by name

Popular brands

National Instruments NI REM-11115, Getting Started Manual

Search results

Summary of Contents for NI REM-11115

Reviews:

Related manuals for NI REM-11115

Brands by name

Popular brands