background image

6

|

ni.com

|

Getting Started with NI 7340/7350 Controllers and AKD Drives

2.

Choose an unused peripheral slot and remove the filler panel.

3.

Touch a metal part on the chassis to discharge any static electricity that might be on your 
clothes or body. Static electricity can damage the controller.

4.

Insert the PXI controller into the chosen slot. Use the injector/ejector handle to fully secure 
the device into place.

5.

Attach the front panel of the PXI controller to the front panel mounting rails of the chassis 
with the slot screws on the chassis.

Caution

Make sure you have correctly connected all safety devices before you 

power on the motion system. Safety devices include inhibits, limit switches, and 
emergency shut down circuits. 

Caution

Always power on the computer containing the motion controller and 

initialize the controller before you power on the rest of the motion system. Power off 
the motion system in the reverse order.

6.

Plug in and power on the chassis.

PCI Controllers

1.

Power off and unplug the computer.

Caution

To protect yourself and the computer from electrical hazards, the 

computer 

must

 remain unplugged until the installation is complete.

2.

Open the computer case to expose access to the PCI expansion slots.

3.

Touch a metal part on the chassis to discharge any static electricity that might be on your 
clothes or body. Static electricity can damage the controller.

4.

Choose an 3.3 V or +5 V PCI slot, and remove the corresponding expansion slot 
cover on the back panel of the computer.

5.

Gently rock the controller into the slot. The connection may be tight, but do

 not 

force the 

controller into place.

Note

Check that the bracket of the device aligns with the hole in the back panel rail 

of the computer chassis.

6.

Secure the mounting bracket of the controller to the back panel rail of the computer.

7.

Replace the cover.

Caution

Make sure you have correctly connected all safety devices before you 

power on the motion system. Safety devices include inhibits, limit switches, and 
emergency shut down circuits. 

Summary of Contents for PCI-7352









































Reviews: