6/9
www.ni.com
Electromagnetic Compatibility
This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:
EN 61326 (IEC 61326): Class A emissions; Basic immunity
EN 55011 (CISPR 11): Group 1, Class A emissions
AS/NZS CISPR 11: Group 1, Class A emissions
FCC 47 CFR Part 15B: Class A emissions
ICES- 001: Class A emissions
Note For the standards applied to assess the EMC of this product, refer to the
section.
Online Product Certification
Note For EMC compliance, operate this device with shielded cables.
CE Compliance
This product meets the essential requirements of applicable European Directives, as amended for CE marking, as follows:
2006/95/EC; Low- Voltage Directive (safety)
2004/108/EC; Electromagnetic Compatibility Directive (EMC)
Online Product Certification
Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit
ni.
, search by module number or product line, and click the appropriate link in the Certification column.
com/certification
Environmental Management
National Instruments is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous
substances from our products is beneficial not only to the environment but also to NI customers.
For additional environmental information, refer to the
Web page at
. This page contains the environmental regulations and directives
NI and the Environment
ni. com/environment
with which NI complies, as well as other environmental information not included in this document.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers At the end of the product life cycle, all products
be sent to a WEEE recycling center. For more information about WEEE recycling centers, National
must
Instruments WEEE initiatives, and compliance with WEEE Directive 2002/96/EC on Waste Electrical and Electronic Equipment, visit
.
ni. com/environment/weee. htm
Backplane
Size
3U- sized; one system slot (with three system expansion slots) and 17
peripheral slots. Compliant with IEEE 1101.10 mechanical packaging. PXI
Express Specification compliant. Accepts both PXI Express and CompactPCI
(PICMG 2.0 R 3.0) 3U modules.
Backplane bare- board material
UL 94 V- 0 Recognized
Backplane connectors
Conforms to IEC 917 and IEC 1076- 4-101, and are UL 94 V- 0 rated
System Synchronization Clocks (PXI_CLK10, PXIe_CLK100, PXIe_SYNC100)
10 MHz System Reference Clock: PXI_CLK10
Maximum slot-to- slot skew
1 ns
Accuracy
±25 ppm max. (guaranteed over the operating temperature range)
Maximum jitter
5 ps RMS phase- jitter (10 Hz– 1 MHz range)
Duty- factor
45%–55%
Unloaded signal swing
3.3 V ±0. 3 V
Note For other specifications refer to the
.
PXI-1 Hardware Specification
100 MHz System Reference Clock: PXIe_CLK100 and PXIe_SYNC100
Maximum slot-to- slot skew
100 ps
Accuracy
±25 ppm max. (guaranteed over the operating temperature range)
Maximum jitter
3 ps RMS phase- jitter (10 Hz– 12 kHz range), 2 ps RMS phase- jitter
(12 kHz– 20 MHz range)
Duty- factor for PXIe_CLK100
45%–55%
Absolute single- ended voltage swing (When each line in the differential pair
has 50 W termination to 1.30 V or Thévenin equivalent)
400 –1000 mV
Note For other specifications refer to the
.
PXI-5 PXI Express Hardware Specification