background image

Where to Go Next................................................................................................................... 13

Worldwide Support and Services............................................................................................13

Safety Guidelines

Caution

 

You can impair the protection provided by the PXIe-5763 if you use it in

a manner not described in this document.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

FlexRIO Documentation and Resources

Table 1.

 FlexRIO Documentation and Resources

Document/Resource

Location

Description

 

 

 

PXIe-5763 Getting
Started Guide

 (this

document)

Available from the Start menu

and at 

ni.com/manuals

.

Contains installation instructions

and basic programming instructions

for your PXIe-5763.

PXIe-5763
Specifications

Available from the Start menu

and at 

ni.com/manuals

.

Contains specifications for your

PXIe-5763.

LabVIEW FPGA
Module Help

Embedded in 

LabVIEW Help

and at 

ni.com/manuals

.

Contains information about the

basic functionality of the LabVIEW

FPGA Module.

2

  | 

ni.com

  | 

PXIe-5763 Getting Started Guide

Summary of Contents for PXIe-5763
















Reviews: