background image

11. (Optional) Configure the DAQ device or module connected to the SCB-100A by

completing the following steps.
a.

In MAX, right-click your DAQ device or module and select 

Configure

.

b.

Configure the device or module properties and click 

OK

.

12. Test specific device functionality. Run a Test Panel in MAX by right-clicking your DAQ

device or module and selecting 

Test Panels

. Click 

Start

 to test the device or module

functions.

Note

 

When you have finished using the SCB-100A, power off any external signals

connected to the SCB-100A before you power off your computer.

Mounting the SCB-100A

You can use the SCB-100A on a desktop, or mount it to a panel or a standard DIN rail. For
two-dimensional drawings and three-dimensional models of the SCB-100A, visit 

ni.com/

dimensions

 and search by product name.

Panel Mounting

Three keyholes are located on the back of the SCB-100A for mounting it to a panel or wall. To
mount the SCB-100A to a board or panel, complete the following steps.
1.

Download and print the panel mounting template PDF by going to 

ni.com/info

 and

entering the Info Code 

scb100amounting

.

2.

Using the template, mark the three points on the panel. Verify that the narrow ends of the
panel mounting screw keyholes are pointing up.

3.

Screw #6-32 panhead machine screws or M3 panhead machine screws into the points
marked on the panel, leaving room to easily remove the SCB-100A from the panel.
Installed screw height for both screw types (from the wall to the top of the screw) is
5 mm (0.2 in.).

DIN Rail Mounting

The NI 9913 DIN rail mounting kit (part number 781740-01) contains one clip for mounting
the SCB-100A on a standard 35 mm DIN rail. Fasten the DIN rail clip to the accessory using
two FLH #6-32 x 5/16" screws (included in the kit) with a #2 Phillips screwdriver, as shown in
the following figure.

Note

 

The threaded holes on the SCB-100A for DIN rail mounting should not be

used more than five times. Unscrewing and reinstalling the DIN rail clip will
produce a compromised connection between the DIN rail clip and accessory.

6

  | 

ni.com

  | 

SCB-100A User Guide

Summary of Contents for SCB-100A













Reviews: