background image

MAIN

BATT

SOLAR

PANEL

INPUT

If a standard solar panel is used, it can be connected to the input marked "SOLAR PANEL".

Before installing a battery into the Power Pack DC40, select the correct battery type. 

(Instructions on page 7)

Make sure all connections are secure and terminated correctly with appropriate tools.

For applications where the Power Pack DC40 is installed in a vehicle, locate the Power Pack such that 
the input cables are not restricted or under strain. The Power Pack should also be secured to prevent 
movement.

The input cables must be terminated with a RED 50A coupler matching the input on the Power Pack 
DC40 marked "MAIN BATT".

Once the battery type is selected, a battery can be installed into the Power Pack DC40 and the RED 
input cable connected 

(Fig 2)

.

2

Use 16mm  cables for the input from the vehicle main battery and install the supplied 50A in-line fuse 
close to the main battery on the positive cable (

Fig 1).

Connect the supply from the main 
battery (alternator) to the RED input 
on the Power Pack DC40.

Ensure terminals are crimped securely.

Install the fuse on the positive cable 
close to the main battery.

Fig 1

Fig 2

6

Preparing for Installation

Summary of Contents for DC40























Reviews: