Original Language Version
V
VV
To move the compressor, use the handle only. Maintain unit’s centre of gravity when lifting.
DO NOT
attempt to lift or move the
compressor by any other means.
V
VV
Use the compressor in a well ventilated area and ensure it is placed on a firm surface.
V
VV
Keep tools and other items away from the compressor when it is in use, and keep area clean and clear of unnecessary items.
V
VV
Ensure the air hose is not tangled, twisted or pinched.
V
VV
Keep children and unauthorised persons away from the working area.
V
VV
DO NOT
dis-assemble compressor for any reason. The unit must be checked by qualified personnel only.
DO NOT
carry out any welding operations on any pressurised parts of the vessel.
V
VV
DO NOT
use the compressor outdoors, or in damp, or wet, locations.
V
VV
DO NOT
operate within the vicinity of flammable liquids, gases or solids.
V
VV
DO NOT
touch compressor cylinder, cylinder head or pipe from head to tank as these may be hot.
V
VV
DO NOT
use this product to perform a task for which it has not been designed.
V
VV
DO NOT
deface the certification plate attached to the compressor tank.
V
VV
DO NOT
cover the compressor or restrict air flow around the unit whilst operating.
V
VV
DANGER! DO NOT
direct the output jet of air towards people or animals.
DO NOT
operate the compressor without an air filter.
DO NOT
allow anyone to operate the compressor unless they have received full instructions.
V
R
VV
WARNING!
The air tank is a pressure vessel and the following safety measures apply:
DO NOT
tamper with the safety valve,
DO NOT
modify or alter the tank in any way and
DO NOT
strap anything to the tank.
DO NOT
subject the tank to impact, vibration or to heat and
DO NOT
allow contact with abrasives or corrosives.
V
R
VV
WARNING!
If an electrical fuse blows, ensure it is replaced with an identical fuse type and rating.
When not in use, store the compressor carefully in a safe, dry, childproof location.
2. INTRODUCTION
All models feature aluminium cylinder heads fitted with aluminium motor windings. Cast iron cylinder gives added resistance to wear.
Suitable for general purpose applications. Pump head directly coupled to induction motor for quiet operation. Welded tank complies with latest
European standards. Fitted with fully automatic pressure
cut-out switch with twin gauges displaying tank and working pressures. Fitted with
non-rewireable plug.
3. SPECIFICATION
MODEL:
.....................................................................
NA2420E
Motor output: ....................................................................... 2hp
Voltage/Phase: .........................................................230V - 1ph
Rated supply: ...................................................................... 13A
Air displacement: ............................................... 6.8cfm(193l/m)
Maximum free air delivery: ................................ 4.6cfm(130l/m)
Tank capacity: ..................................................................... 24ltr
Maximum pressure: .................................................116psi/8bar
Weight: ...............................................................................27kg
Dimensions (W x D x H): ........................... 600 x 290 x 585mm
4. PREPARATION & ASSEMBLY
4.1.
Remove compressor from packaging and inspect for any shortages or damage. If anything is found to be missing or damaged, contact your
supplier.
4.2.
Confirm that the mains voltage corresponds with the voltage shown on the compressor data plate.
4.3.
The compressor should be installed on a flat surface, or one that does not exceed 10
°
either transversely or longitudinally,
(see fig.2) and should be in a position that allows good air circulation around the unit.
4.4.
The compressor is supplied without oil in it. The oil is in a separate container. Remove the transit plug from the oil filler
aperture, pour oil into the aperture until it has reached the correct level on the sight (fig.3). Fit the oil filler/breather supplied into the
aperture.
4.5.
Ensure that the air vent in the oil filler/breather is free from debris. If the air vent is blocked, pressure can build up in the crankcase causing
damage to the compressor and possible personal injury.
4.6.
If it is not already fitted, screw the air filter holder into the inlet port (fig.4).
fig.1
fig.2
fig.3
fig.4
NA2420E | Issue 1 20/05/16
