background image

a)  Carefully lay instrument on its side, taking care to avoid damage to the specimen slide holder located on 

top of mechanical stage. 

 

b)  Loosen large chrome locking screw located on hinged door of illuminator base. 

 

c)  Swing door open to expose the halogen lamp. 

 

d)  Using a tissue or cloth to gently grasp the halogen bulb, pull straight out of lamp socket. 

 

e)  Your microscope requires a 12 volt, 20 watt halogen bulb,  available from the dealer from which you 

purchased your microscope.  This is a common microscope bulb, Osram #64425. 

 

f)  Make certain that new bulb is clean, as fingerprints on bulb can affect light transmission.  Grasping bulb 

gently with a tissue or cloth, insert pins straight into lamp socket. 

 

g)  Carefully clean lamp to assure that it is clean and free of all fingerprints. 

 

h)  Close hinged door and tighten locking screw. 

 
 

TROUBLESHOOTING 

 

PROBLEM 

REASON FOR PROBLEM 

SOLUTION 

Light fails to operate. 

Outlet inoperative. 

Have qualified service technician repair 
outlet. 

 

 

 

 

AC power cord not connected. 

Plug into outlet. 

 

 

 

 

12 volt DC output plug not 
plugged into DC power jack 

Plug 12 volt DC output plug into DC 
power jack 

 

 

 

 

Lamp burned out. 

Replace lamp. 

Lamp flickers 

Lamp loose in socket. 

Push lamp pins into lamp socket. 

Image does not focus 

Cover slip on specimen slide 
too thick. 

Use 0.17mm thick cover slip. 
 

 

 

 

 

Slide upside down. 

Place slide on stage with cover slip 
facing up. 

Image does not remain in focus  Stage drops down from its own 

weight. 

Adjust tension of coarse focus knob. 

Poor resolution 
     (image not sharp) 

Objective lenses dirty. 

Clean objective lenses. 

 

 

 

 

Eyepiece lens dirty. 

Clean eyepiece lenses. 

 

 

 

 

Too much light. 

Adjust intensity of light and check iris 
diaphragm aperture. 

Spots in field of view. 

Eyepiece lens dirty. 

Clean eyepiece lenses. *** 

 

 

 

 

Specimen slide dirty. 

Clean slide. 

 

 

 

 

Condenser lens dirty. 

Clean lens of condenser. 

***Spots in field of view can also result from dirt on inside of eyepiece.  It is recommended that you have 
service technician clean inside of lens. 

 
OPTIONAL ACCESSORIES AND PARTS: 

 
#610-160 WF10X 

Eyepiece 

#610-160R 

WF10X eyepiece w/reticle, 10mm/100div. 

#704-160 

DIN 4X objective lens, 0.10 N.A. 

#710-160 

DIN 10X objective lens, 0.25 N.A. 

#740-160 

DIN 40X objective lens, 0.65 N.A. 

#799-160 

DIN 100X objective lens, 1.25 N.A. 

#704-160P 

DIN 4X Plan objective lens, 0.10 N.A. 

#710-160P 

DIN 10X Plan objective lens, 025 N.A. 

#740-160P 

DIN 40X Plan objective lens, 0.65 N.A. 

#799-160P 

DIN 100X Plan objective lens, 1.25 N.A. 

Summary of Contents for DC3-163











Reviews: