3
System Attachments
4
Install - Above Sink
The Natural Kitchen comes with a diverter valve designed to fit the majority of
standard male and female faucets with removable aerators.
If you have a designer or commercial faucet, extendable hose or non-standard
spout you may need to replace your faucet or install your Natural Kitchen under
your sink with the Under Sink Adaptor Kit - sold separately.
Step 1.
Remove Aerator
Unscrew the faucet aerator
using your hand or a small tool
such as pliers or a wrench.
Optional:
Female Faucet
The male adaptor may require
an extra washer to fit some
spouts. Use the washer from
the recently removed aerator
(Step 2) if needed.
Step 6:
Check for Leaks
If you spot a leak check to
make sure the rubber washer
is in place. If the faucet
surface is damaged teflon
tape may help achieve a seal.
Teflon Tape
Step 7.
Flush your System
Let filtered water run for 3 - 5
minutes. This will eliminate air
in the line and flush carbon
fines from the cartridge.
Your unit is now ready for use.
Step 3.
Cleaning
Clean the spout threads. To
remove dirt, use an old tooth-
brush and flush with water.
Step 2.
Retain Washer
The aerator & washers may
be needed later. Set these
pieces aside for safe-keeping.
Step 5a.
Female Faucet
If your faucet is female, first
attach the male adaptor to
the spout by threading the
fitting on clockwise. A coin
can be used to tighten
.
Step 5b:
All Faucets
Connect the diverter to the
male faucet or adaptor by
turning the threaded collar
on the top of the diverter
clockwise until it is finger tight.
Step 4.
Determine Threads
A
female faucet
has threads
on the
inside
. A
male faucet
has visible threads on the
outside
.
1.
1/4” OD LLDPE Tubing (10’)
2.
Inlet/Outlet Fittings
1/4” Compression Nut (2)
1/4” Plastic Sleeve (2)
1/4” Brass Insert (2)
3.
Shut-Off Valve
(Attached)
1/4” Compression Nut (1)
(Attached)
1/4” Plastic Sleeve (1)
1/4” Brass Insert (1)
4.
T-Valve
5.
Optional Fittings
(
For Copper Cold-Water Lines)
3/8” Compression Nut (1)
3/8” Brass Sleeve (1)
6.
Faucet Mounting Hardware (5)
7.
Faucet Fittings
1/4” Compression Nut (1)
1/4” Plastic Sleeve (1)
1/4” Plastic Insert (1)
8.
Faucet
1
2
5
4
6
3
7
8
Under Sink Attachments
Above Sink Attachments
1.
1/4” Above Sink Dual Tubing (5’)
2.
Diverter Valve
15/16” 27-Thread Female
Attached Rubber Washer
3.
Male/Male Adaptor
15/16” x 55/64” 27-Thread Male
Attached Rubber Washer
Optional Male/Male Adaptor
(sold seperately)
13/’16” x 55/64” 27-Thread Male
Attached Rubber Washer
1
2
3
Threaded
Collar
The Natural Kitchen comes with either Above Sink or Under Sink attachments.
If you decide to convert your system later, attachment kits are sold seperately.
Mounting Bracket:
Naturally Filtered offers an optional mounting bracket
accessory for Under Sink installations. This bracket attaches your Natural
Kitchen upside down to the cabinet under your sink. The bracket places your
system out of the way. The bracket is also recommendedd if you intend to
hard-plumb with copper lines. Contact Naturally Filtered or your local Dealer for
more details.
