background image

Electric Boiler Controller NELBC-1

Timers 

– Setting  and activation of time intervals  in which heating is allowed, as well  as the

temperature that the boiler must maintain. If at least one of the three timers is active and the
"Timers" mode is turned on, the heating will only work in the intervals set by the active timers!
Outside the intervals of the activated timers, the heating will not work.

Have in mind that the time in column "

On

" cannot be later than the time in column "

Off

", so it may

be necessary to modify the time in column "

Off

"  first and after that the time in column "

On

"!

When the boiler is in Timers mode then there is a timer icon on the top information bar of the main
screen. The icon is red when heating is forbidden by timers and green when heating is working and
the effective set temperature is defined by the timer. 

This screen may also be reached directly form the main screen whenever the boiler is in Timers
mode by pressing the timer icon on the top information bar.

Display 

– Parameter "Brightness" changes the brightness of the display. If option "Display date" is

on then the date is always displayed as one of the messages that change over on the bottom
information bar of the main screen. If option "Display date" is off then the date is displayed only if
there is no other information to be displayed. Option "Auto lock" activates the automatic lock of
the screen

 

30 seconds after the last action. Option "Dimming" activates dimming of the display 30

seconds after the last action.  When the display is dimmed any touch of the screen reverts it to
normal brightness.

User Manual / revision 1.2     

 

http://www.naturela-bg.co

 

 m/

   en 

стр. 25 от 36

The timer is active only

in days of week

with LED on

Switch to activate the timer

Days of week

Set temperature

Summary of Contents for NELBC-1





































Reviews: