background image

16 NETWORK SETTINGS

IP Setting Fields

Definition

Connection Status

Status of connection

MAC Address

Ethernet MAC Address

Tx/Rx Msgs

Number of transmitted and  

received messages

Tx/Rx Msgs Dropped

Number of unanswered Tx or Rx 

messages

7.2.2    Update Wi-Fi Client Settings

From the FS-GUI Network Settings landing page, click on the 

Wi-Fi Client tab. To change the Wi-Fi client settings, follow these 

instructions:

1.  Set the Wi-Fi Status to ENABLED for the gateway to 

communicate with other devices via Wi-Fi. 

2.  Enter the Wi-Fi SSID and Wi-Fi Password for the local wireless 

access point.

3.  Enable DHCP to automatically assign all Wi-Fi Client network 

settings or manually modify the setting using the fields 

immediately below (IP Address, Network, etc.).

Note

If connected to a router, set the IP gateway to the 

same IP Address as the router.

4.  Click Update Wi-Fi Settings, then click on System Restart to 

restart the gateway and activate Wi Fi Client settings.

5. 

Go to Common settings (Section 7.2.3) to set the Primary 

Connection to Wi-Fi Client.

7.2    Change the Gateway IP Address

Configure the IP settings of the gateway in the following methods:

 

When using the Ethernet port to connect to the local network 

(

Section 7.2.1

).

 

When connecting the gateway to a local wireless access point, 

configure the Wi-Fi Client Settings in the gateway (

Section 

7.2.2

).

Note

For Wi-Fi Access Point network information see 

Appendix B.4

.

7.2.1    Update Wired Network Settings

IP Settings tab is the landing page when selecting Network 

Settings on the navigation tree. To change the IP settings, follow 

these instructions:

1.  Enable DHCP Client State to automatically assign IP Settings 

or modify the settings manually as needed, via these fields: 

IP Address, Netmask, Default Gateway and Domain Name 

Server1/2.

Note

If connected to a router, set the Default Gateway to the 

same IP Address as the router.

2.  Click Update IP Settings, then click on System Restart to restart 

the gateway and activate the new IP Address.

3.  Connect the gateway to the local network or router.

Note

If the FS-GUI was open in a browser, the browser 

will need to be pointed to the new IP Address of 

the gateway before the FS-GUI will be accessible 

again.

Figure 26: FS-GUI Ethernet Port Network Settings

Summary of Contents for Modbus/BACnet Gateway








































Reviews: