background image

7

About the Boiler

2.1    Description of the Boiler

The Navien NCB-H boiler is available in 5 models: 

NCB-190/060H, NCB-190/080H, NCB-240/110H, 

NCB-240/130H and NCB-250/150H.

The main features are as follows:

 

Power Interruption: When the power is restored 

after a power failure, the boiler will automatically 

start and return to normal operation. A manual 

reset is not required.

 

Freeze Protection: A sensor inside the boiler 

automatically detects the temperature and, 

if necessary, initiates a safety heating cycle to 

prevent internal equipment damage due to 

freezing temperatures.

 

Short-Circuit Protection: Any short-circuit 

occurring in the boiler’s electrical circuit 

immediately blows the internal glass fuses and 

automatically cuts off the gas supply.

 

Lightning Protection: Each boiler is specially 

grounded, both internally and externally, to 

protect against lightning strikes.

 

Carbon Monoxide Protection: The boiler is 

designed to maintain a safe air-to-gas ratio and 

combustion rate. This function is continuously 

monitored by the boiler’s air ratio control module.

 

Auto Fan Detection: The rotation of the fan is 

automatically detected and controlled. Fan failure 

will stop the operation of the boiler.

 

Boiling Prevention: Excessive temperatures will 

automatically stop the boiler.

2.2    Parts of the Boiler

2.2.1    Front View

Exhaust  

Gas Vent

Combustion  

Air Intake

2.2.2    Bottom View

12.8” (325 mm)

3.5”

(88 mm)

3.3”

(85 mm)

2.9”

(74 mm)

2.5”

(63 mm)

2.7”

(68 mm)

17.3” (440 mm)

9.6” (244 mm)

2.4” (60 mm)

2.4” (60 mm)

A

G

B

E

C

F

D

2.7”

(69.5 mm)

#

Description

A

Heating Supply

B

Domestic Hot

C

Gas Connection

D

Domestic Cold

E

Auto Feeder Inlet (Make-up Water)

F

Condensate Outlet

G

Heating Return

2.    About the Boiler

Summary of Contents for NCB-190/060H
































Reviews: