background image

Safety Information        5

DANGER

HOT

BURN

To prevent burns:

 

Use the lowest operating temperature 

setting necessary to provide 

comfortably hot water.

 

If your household has children or 

elderly or disabled residents, consider 

using a lower temperature setting.

 

Read all the instructions in this 

manual carefully before changing the 

temperature setting.

 

Feel the water before using it on 

children, the elderly, or the disabled.

DANGER

This boiler’s water temperature is set to 

49°C at the factory for your safety and 

comfort. Increasing the temperature 

increases the risk of accidental scalding. 

Water temperatures at or above 52°C 

can cause instant scalding or severe 

burns. Before you decide to change the 

temperature setting, read the following 

charts carefully.

Water 

Temperature

Time in which a young child can suffer a 

full thickness (3rd degree) burn

70°C

Less than 1 second

60°C

1 second

55°C

10 seconds

49°C

10 minutes

37°C

Very low scald risk

CAUTION

 

Do not turn on the boiler unless 

the water and gas supplies are fully 

opened. 

Doing so may damage the boiler.

 

Do not turn on the water if the cold 

water supply shut-off valve is closed. 

Doing so may damage the boiler.

 

Do not use this boiler for anything 

other than its intended purpose, as 

described in this manual.

 

Do not remove the front cover unless 

the power to the boiler is turned off 

or disconnected. 

Failure to do so may result in electric 

shock.

 

When servicing the controls, label all 

wires prior to disconnecting them. 

Failure to do so may result in wiring 

errors, which can lead to improper or 

dangerous operation. Verify proper 

operation after servicing.

 

Do not use unapproved replacement 

or accessory parts. 

Doing so may result in improper or 

dangerous operation and will void the 

manufacturer’s warranty.

 

Do not place anything in or around 

the flue terminals, such as a clothes 

line, that could obstruct the air flow 

in or out of the boiler.

 

This boiler has been approved for 

use the UK and Ireland only. 

Using the boiler in any other country 

will void the manufacturer’s warranty.

Summary of Contents for NCB500-1.5S/37K









































































Reviews: