background image

98        Replacement of Parts

9.  Check that all gas connections are tightly sealed to ensure 

that no gas leaks are present.

10.  Turn on water supply, power supply, and gas supply to the 

unit.

11.  Verify the gas pressures to the unit with the values provided 

in this Service Manual.

6.2.7    Condensate Trap

1.  Turn off the gas supply to the unit.

2.  Disconnect the unit from the power supply.

3.  Turn off the water supply to the unit.

4.  Remove the pin that secures the condensate drain cap 

and then remove the cap. Use a bucket to collect the 

condensate.

Figure 13

5.  Detach the condensate piping from the unit.

6.  Remove the two screws located at the bottom of the unit 

that are attached to the condensate trap. 

7.  Loosen the clip that secures the hose to the condensate 

trap, and then pull off the hose.

8.  Remove the old condensation trap and replace it with the 

new part.

9.  Reconnect the hose to the condensate trap.

10.  Reattach the condensation trap to the unit and secure it 

using the five screws.

11.  Replace the front panel to its original position.

12.  Turn on the water supply, power supply, and gas supply to 

the unit.

Note

Ensure that the condensate drain trap is completely 

inserted into the condensate fitting to eliminate 

leaking. Use the pin to secure the cap to the fitting.

6.2.6    Main Gas Valve

1.  Turn off the gas supply to the unit.

2.  Disconnect the unit from the power supply.

3.  Turn off the water supply to the unit.

4.  Remove the two screws and disconnect the wiring 

connector at the gas valve.

Figure 11

5.  Remove the two screws located at the bottom of the unit 

that are attached to the gas valve.

Figure 12

6.  Replace the old gas valve with the new part.

7.  Reconnect the gas valve assembly to the unit by using the  

two screws at the boiler.

8.  Reattach the gas valve wiring connector.

WARNING

Failure to correctly assemble the components according to 

these instructions may result in a gas leak or explosion.

Summary of Contents for NCB500-2S/37K























































































































Reviews: