background image

31

The  GEONAV will insert a waypoint in the port position and
delete automatically the existing route, then go back to
Navigation mode activating automatically the Autozoom
function.

How to delete the whole route

In Navigation mode, it is possible to delete the whole route by
pressing the 

CLR 

key. Press 

ENT 

to confirm or 

CLR 

to abort the

operation.
In Cursor mode, it is necessary to keep the 

CLR 

key pressed for

more than 3 seconds (if the key is kept pressed for a shorter
time, the GEONAV will go back to Navigation mode).

How to edit a route in Cursor mode

It is often necessary to delete a single waypoint or modify its
position; the GEONAV allows performing these operations in a
very simple way and by way of few keys.
• Deleting a route segment

Position the cursor exactly on the segment to delete with the

CURSOR 

key, then press 

CLR 

to confirm.

• Deleting a waypoint in a plotted route

Position the cursor exactly on the waypoint to delete with
the 

CURSOR 

key, then press 

CLR 

to confirm.

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

Summary of Contents for GEONAV 5







































Reviews: