Navman Halo Qube 2 Installation Manual Download

Page: 11 / 16

Qube 2

Combination GPS/GPRS
Antenna

ConEx Unit

Connect Vehicle Power
Connections here

Halo QUBE 2

Installation Manual V1.0

Connecting an External ConEX

Note: Please check with your distributor, to see if this feature is available yet.

An external ConEX would be connected if: The user requires additional IO lines, additional serial capture

port, or has custom ConEX code that needs to be used with their system.
The Qube 2 will connect into the connector marked “HALO - QUBE”. The wire colours do not directly

match. Please connect the Qube 2 using the table below.
Please refer to the ConEX installation manual for all other ConEX connections.

RJ45 Connector - Cable A Male plug, Cable B Female socket

ConEX

Connections

Cable A

Cable B

Qube 2

Function

Description

Red

+12/24 V

Power

Pink

Ignition

Do not connect

DB9 - Pin 3

Purple

TxD

Serial data output

DB9 - Pin 2

Brown

RxD

Serial data input

Black

GND

Ground

Note: The MDT port on the ConEX box will no longer function. Please use the RJ45 connector on the Qube 2 cable to
attach an MDT / PDT etc.

Summary of Contents for Halo Qube 2

















Search results

Summary of Contents for Halo Qube 2

Reviews:

Related manuals for Halo Qube 2

Brands by name

Popular brands

Navman Halo Qube 2, Installation Manual

Search results

Summary of Contents for Halo Qube 2

Reviews:

Related manuals for Halo Qube 2

Brands by name

Popular brands