EN
41
1
Handle
2
Engine brake lever
3
Drive lever with line
4
Clamp lever
5
Starter handle with cable
6
Starter cable attachment point
7
Basket
8
Rear wheel
9
Handle connection nut with housing
10
Water cleaning system connection
11
Front wheel
12
Air filter cover
13
Engine
14
Fuel-filler cap
15
Oil filler cap
16
Muffler
17
Spark plug pipe
18
Side discharge cover
19
Wheel lock lever
20
Side discharge chute
21
Basket full indicator
22
Cable adjustment
23
Grass ejection cover
24
Cutting height adjustment lever
25
Side comb for laying grass
26
Throttle control (if equipped)
ASSEMBLY
The mower handle is factory set in the storage position.
Set the lower handle to the use position, making sure that the handle is between the stops and tighten it with the wing nut.
Set the upper handle to the use position and lock it with the clamping lever
1 (Rys.(Fig.) 3
. Turning the nut
2 (Rys. (Fig.) 3)
changes the length of the clamping lever bolt, thus increasing or reducing the clamping force. Fastening occurs when the clamp
is pressed against the handle in the direction of the arrow
3
on
Rys.(Fig.) 3.
Attention! Too short the bolt with a nut may cause the clamping lever not to be tightened, and consequently damage the lever.
Attention! When unfolding and folding the handle, make sure that the engine brake cable does not break or bend. A bent
or otherwise damaged cord may prevent the mower from working properly.
Fasten the starter rope handle
5 (Rys.(Fig.) 2)
at the attachment point
6 (Rys.(Fig.) 2).
Attention! The starter rope extends with resistance. Pull the engine brake lever towards you and slowly pull the cable out to
the necessary length. Remember that pulling the starter cord vigorously can start the mower.
FILLING THE ENGINE WITH OIL
The engine is not filled with oil at the factory. There may be traces of oil remnants in the engine after factory inspection. Before first start-
up, pour approximately 0.6L of recommended B&S SAE30 engine oil
(Rys.(Fig.) 5A),
checking its level on the dipstick integrated
with the oil filler cap
(Rys.(Fig.) 5B).
The oil level must be between the lines: min. / max.
Original engine oil for B&S SAE30 for lawn mowers is recommended.
The first oil change should be carried out after 5 hours of mower operation, after burning about two fuel tanks. The next oil changes should
be carried out every 25 hours of work, but at least once a year.
Drain the used oil while the engine is still hot.
Summary of Contents for 3001S
