19
The oil level must be between the lines: min. / max.
Original engine oil for B&S SAE30 for lawn mowers is recommended
The first oil change should be carried out after 5 hours of mower operation, after burning about two fuel tanks. The next oil
changes should be carried out every 25 hours of work, but at least once a year.
Drain the used oil while the engine is still hot.
Regularly check the oil level before each use.
If necessary, top up oil.
Attention! Used oil should not be disposed of by accident, dispose of it in the sewage system or directly
into the environment. Take it to an oil disposal point.
REFUELING
Before using, familiarize yourself with the safety, use, handling and storage principles contained in this Operation
Manual.
Fuel should be poured outside, in a place where there is no risk of sparks or flames.
Gasoline should only be stored in suitable containers (canisters) that are approved. Check the condition of fuel
storage containers regularly.
Fuel tanks must be securely closed. For safety reasons, replace damaged fuel filler caps.
Do not use beverage bottles or similar to store consumables, e.g. fuel or oil, as other people, especially children,
could drink from them.
The fuel tank should only be filled outdoors; do not smoke while refueling.
Gasoline should be topped up before starting the internal combustion engine.
Do not unscrew the fuel tank cap or add fuel while the internal combustion engine is running or when the engine is
hot.
Do not overfill the fuel tank! Due to the thermal expansion of the fuel, do not fill the tank above the lower
edge of the filler neck
.
The device must not be stored with the fuel tank filled indoors. The resulting gasoline vapors may come into
contact with open flames and ignite. If the fuel tank needs to be emptied, it should be done outdoors. Before
starting the machine, make sure that there is no spilled fuel on or near the machine. If necessary, wipe off the fuel.
Attention! Gasoline vapors are flammable. Before starting the mower, make sure that the working machine
is not less than 3m from fuel tanks.
OPERATION
BRAKE LEVER
Pull the brake lever before starting the engine
2
to the handle
1 (Fig. 5).
By releasing the brake lever, the engine and cutting knife stop.
ENGINE STARTING
Warning!
When the engine is running, the cutting blades rotate.
1.
Check the oil level
(Fig. 4).
2.
Fill the fuel tank with clean, unleaded gasoline. Make sure the spark plug wire is connected to the spark plug.
3.
Press the suction pump 3-4 times
12 (Fig. 6
) (if present).
4.
Stand behind the mower as shown in figure no
7.
5.
Hold the brake lever with one hand
2 (Fig. 5)
in the working position as shown in the figure.
6.
With your other hand, grasp the starter cord handle
5 (Fig. 7
).
7.
Lightly pulling the cord towards you, remove the starter slack, and when you feel resistance, pull the cord hard and
vigorously
5 (Fig. 7)
and let it slowly go back to its place.
8.
Do not release the line handle until the line is pulled through the starter return system.
9.
If the engine does not start after 5-6 strokes, follow the directions in the "Inspection and Troubleshooting" chapter.
Summary of Contents for 5000S
