background image

 

 15

Basic Operation 

1.  Use a 3.5mm male to male line in cable (included) to connect the Line-out or Headphone out jack 

of an audio device to this system Auxiliary Line-In jack. 

2.  Press POWER to turn the player on . 
3.  Set the FUNCTION Mode switch to the “AUX” position . 
4.  Start playback on the external audio device. 

◆ 

You must use the external audio device to control playback. 

◆ 

To avoid distortion, do not set the volume from the external audio device to very high levels. 

 

 

TROUBLESHOOTING 

 
There is no power to the device .

 

◆ 

Ensure that the power cord is securely connected to the unit and the proper wall outler . 

◆ 

Ensure that the voltage selector has been set properly . 

There is no sound .

 

◆ 

Ensure that the speaker connections are secure and correct . 

◆ 

Try to adjusting the volume . 

◆ 

Ensure that the player is in the proper mode(CD.UDISK,RADIO) 

◆ 

Ensure that headphones are not connected to the unit. 

The sound is distorted . 

◆ 

The unit may be positioned too closely to a large appliance (e,g a TV or refrigerator ). If 
possibel ,turn the appliance off or move the unit to another location . 

◆ 

Ensure that the raido is in broadcast reception range . 

◆ 

Decrease the volume level . 

The remote control doesn’t work.

 

◆ 

Ensure that there are no obstacles between the remote and the player. 

◆ 

Point the remote at the remote sensor on the main unit . 

◆ 

Strong light(e.g, direct sunlight ,fluorescent lights , strobe lights )may interfere with the remote 
signal . 

◆ 

Ensure that the batteries in the remote control retain a charge and have been installed correctly . 

◆ 

Try replacing the remote’s batteries . 

The device does not play . 

 

◆ 

Moisture may have condensed inside the player .Remove the disc and leave the player on for 
1-2hours and then try again . 

The USB disk or SD/MMC card doed not play.

 

◆ 

Use only USB-MSC device of flash disk drives . USB-MTP devices are not supported . 

◆ 

Ensure that the USB disk or SD/MMC card has been loaded with compatible MP3 or WMA files. 

◆ 

Ensure that the capacity of the SD/MMC card does not exceed 2GB. High- capacity SD 
cards(HCSD) are not supported by this player. 

◆ 

DRM-encrypted WMA files are not supported . 

The CD will not play.

 

◆ 

Ensure that the CD has been loaded with its label facing up . 

◆ 

Ensure that the CD is not damaged , scratched ,or dirty . 

◆ 

Ensure that the CD is an audio CD ,or that it contains compatible MP3 or WMA files . 

◆ 

DRM-encrypted WMA files are not supported . 

Summary of Contents for NSM-436


















Reviews: